Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 56 of 175
The wire harness connected to the fuel pump has inappropriate material properties. During vehicle operation, connector terminal contact deteriorates, resulting in poor electrical continuity. This can cause the pump to malfunction, potentially …
① Battery positive cable routing is improper in some vehicles, causing the cable to contact the engine support. Engine vibration may damage the cable insulation, potentially resulting in short circuit and fire.
In the front and rear suspension arms, improper material selection in the chassis-side ball joint may cause corrosion of the joint. This reduces the strength of the joint and, in the worst …
In automatic transmissions, improper soldering of electrical circuit boards within the lead frame may cause cracks due to thermal stress. This can prevent vehicle speed signals from being transmitted to the PCM …
Gasoline engine vehicles have engine control computers with electrolytic capacitors used in the injector drive power circuit that may have internal damage due to improper manufacturing process. Continued use can cause further …
The fuel tank breather hose (which vents air from the fuel tank during refueling) is made of unsuitable material. Heat from the exhaust system can cause the hose to deteriorate and develop …
The sound-insulating material in the engine compartment has insufficient clearance from the exhaust manifold and lacks fixed attachment points in certain areas. Consequently, portions of the sound-insulating material may deform due to …
Horn switch wiring has inadequate routing design, and in some assembly cases, the wiring contacts the steering column bracket. Vibration during driving can damage the wire insulation, causing a short circuit that …
In the steering apparatus of low-floor two-axle heavy-duty trucks, the clamp bolt/nut fastening torque on the left side of the front axle tie rod is inappropriate, causing reduced clamping force. This creates …
Trailer axles manufactured by automatic welding machines with inadequate process control exhibit insufficient weld penetration in some units. This can cause cracks to develop in the axle. Continued operation may propagate these …
Some alternators with insufficient generating capacity were installed during manufacturing. When high electrical loads are drawn, such as during electric hydraulic power steering operation, the alternator experiences excessive electrical load, causing internal …
Due to an improper control program in the meter cluster panel, the meter cluster panel may restart when displaying a message indicating low fuel level. As a result, while driving, the speedometer …
In the brake master cylinder, the secondary cup has improper material and shape. The cup swells due to plasticizers from the brake fluid dissolving from the reservoir tank hose, and expands due …
In large and medium-sized buses with independent front-wheel suspension, improper manufacturing of the center member allows water containing de-icing agents and similar substances to infiltrate the interior, causing corrosion near the lower-arm …
During the manufacturing process of medium-duty trucks, improper writing of configuration values to the body control module has resulted in some units being written with values that do not match vehicle specifications. …
In the electric parking brake, the abnormality detection program in the control computer power circuit is inappropriate. When the battery is degraded, a voltage drop during restart from idle stop may be …
In the airbag control system, improper manufacturing conditions of the IC chip within the acceleration sensor can cause internal circuit breaks. This may cause the airbag warning light to illuminate and the …
During the fuel rail manufacturing process, improper brazing of the fuel rail end cap can result in braze cracks. Fuel may seep from the affected area, which in the worst case could …
During fuel rail manufacturing, improper brazing of the fuel rail end cap can result in braze cracking. Fuel may seep from the affected area, potentially leading to fire in severe cases.
In the continuously variable transmission (CVT) controller, improper manufacturing control of resistors mounted on the internal circuit board causes cracks to develop at solder joints, resulting in increased resistance values. This may …
① In asphalt finishers, improper manufacturing or component management of the vehicle control computer has resulted in circuit board cracks or IC chip circuit shorts. Continued use may cause malfunctions in controlled …
The electrostatic discharge wiring within the steering column module may be improperly assembled, causing it to break when the steering wheel is operated beyond its range of motion. Additionally, due to improper …
The inflator (inflation device) of the passenger-side airbag may deteriorate under prolonged temperature fluctuations in high-temperature, high-humidity conditions. During airbag deployment, the inflator container may rupture, potentially injuring occupants.
The inflator in the passenger-side airbag may degrade under prolonged exposure to high temperature and humidity conditions. During airbag deployment, the inflator container may rupture, potentially injuring occupants.
The meter panel software that calculates brake disc wear is inappropriate. Under certain conditions, the calculated wear value resets. As a result, the brake disc wear warning light does not illuminate, and …
The gaskets for the fuel filler cap bracket and fuel level sensor mounting point in the fuel tank have improper geometry, which may cause gaps at the mounting areas. When the vehicle …
① During the manufacturing process of the fuel pump that adjusts the fuel level difference between the right and left sides of the fuel tank, the fuel supply valve was damaged, causing …
① During fuel pump manufacturing for balancing fuel tank left/right level, the fuel supply valve was damaged in some units, causing malfunction. This prevents fuel delivery to the engine despite fuel remaining …
In the engine blowby gas recirculation device, improper molding of the blowby gas heater causes cracks in the outer resin. When moisture enters these cracks, they expand and cause the electric heating …
In the forklift load handling and steering hydraulic control controller, the rotation control program for the hydraulic pump motor is inappropriate. When the load handling lever is fine-adjusted such that the hydraulic …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.