Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 71 of 175
In the fuel system, the wiring that supplies electrical power to the fuel pump has been manufactured improperly, resulting in damage to the wire insulation in some vehicles. Continued operation in this …
In large buses, improper tightening of the front brake hose connection results in insufficient fastening force at the joint. Continued operation may cause the connection to loosen, leading to air leakage and …
In large buses, front brake hoses may have insufficient fastening torque at connection points due to improper tightening during assembly. Continued operation may result in loose connections, air leakage, and potential loss …
The exterior door handle design on the passenger/cargo door is defective. When the handle is pulled, moisture-absorbed movable components swell and interfere with the handle case, causing jamming and failure to return …
Rear axle stabilizer bars may not be bent to design specification due to inadequate manufacturing control. During use, excessive stress on the stabilizer bar can cause cracking. Continued use in this condition …
The passenger-side airbag inflator may experience propellant degradation when exposed to prolonged temperature fluctuations in hot, humid conditions. During airbag deployment, the inflator container may rupture, risking occupant injury.
The terminals inside the ignition switch may wear due to engine vibration, resulting in poor contact between terminals. This can cause communication failure between the ignition switch and body control module, leading …
In the engine fuel pipe, connector bolt fastening work was performed improperly, resulting in insufficient clamping force in some units. Consequently, the connector bolt may loosen and cause fuel leakage, which in …
In road work vehicles modified to enable steering operation from both driver and passenger seats, improper routing instructions for the side marker light electrical wiring prevent power from being supplied to the …
In vehicles equipped with FSC (Forward Sensing Camera), some units have not completed initial camera setup during the inspection process. As a result, SCBS (Smart City Brake Support) may not operate normally.
The driver-side airbag inflator may experience degradation of the gas generant when subjected to repeated temperature cycles in high-humidity environments. Upon airbag deployment, the inflator container may rupture, scattering component fragments and …
In the fuel piping of excavators and loaders, the pre-filter (fuel filter) that protects the fuel pump is installed at an improper angle. Moisture generated by temperature changes may freeze during winter, …
In large truck and bus engine control programs, improper low-temperature correction control can cause cracks to develop above the piston pin hole. Continued operation in this condition allows crack propagation to damage …
In certain driver-seat airbag inflators, inadequate moisture protection of the gas generant can lead to degradation when subjected to repeated temperature cycles in high-humidity environments. This may cause the inflator container to …
The gas generant in the driver-side airbag inflator may degrade due to prolonged use in high-temperature, high-humidity environments. This can cause abnormal pressure rise within the inflator during airbag deployment, risking rupture …
In certain driver-side airbag inflators, inadequate moisture protection of the gas generant can cause degradation when subjected to repeated temperature cycling in high-humidity environments. This may result in inflator container rupture upon …
The gas generator in the driver-side airbag inflator may degrade due to prolonged use in high-temperature, high-humidity environments. This can cause abnormal pressure rise in the inflator during airbag deployment, risking rupture …
In engines for large and medium-sized buses, the weld between the internal arm and shaft that operates the variable nozzle of the turbocharger has insufficient strength. When the actuator is driven, this …
In engines of medium-duty trucks and large/medium-duty buses, the weld between the internal arm and shaft that actuates the variable nozzle of the turbocharger has insufficient strength. Actuation of the actuator can …
The inflator (gas generator) of the passenger-side airbag may degrade when the propellant is exposed to prolonged temperature fluctuations in humid conditions. In the event of airbag deployment, the inflator container may …
The inflator (gas generator) of the passenger-side airbag may deteriorate if the gas generant is exposed to prolonged temperature fluctuations in humid conditions. As a result, the inflator container may rupture during …
The gas generant in the driver-side airbag inflator (gas generator) may degrade when exposed to prolonged temperature fluctuations in humid conditions. Consequently, the inflator housing may rupture upon airbag deployment, causing component …
The driver-side airbag inflator lacks adequate moisture protection for its gas generant, causing degradation through repeated temperature and humidity cycles. This may result in inflator container rupture during airbag deployment.
The passenger-side airbag inflator has inadequate moisture protection of the gas generant, which may degrade due to repeated cycles of temperature and humidity changes. Consequently, the inflator container may rupture during airbag …
The inflator (gas generation device) of the passenger seat dual-stage deployment control airbag has inadequate moisture protection of the gas generant, which may degrade due to repeated temperature and humidity fluctuations. As …
Curtain shield airbag inflators with gas cartridges have inadequate manufacturing processes. Insufficient cleaning of inflator pipes leaves residual lubricant, preventing proper welding. Microscopic cracks develop at weld seams. When vehicle interior temperature …
In shovel loaders, the hydraulic hoses for operating the rotary snow removal attachment were selected inappropriately, resulting in low-pressure-rated hoses being installed in high-pressure sections. Consequently, during snow removal operations, hydraulic pressure …
Incorrect wheel bearing spare parts were shipped, resulting in some vehicles being fitted with wrong components. Continued use in this condition causes bearing separator wear, generating metal particles that accelerate bearing grease …
In the electrical system, improper routing design of electrical wiring may cause contact between the electrical wiring and the seat slide mechanism. This can damage the insulation of the electrical wiring, causing …
Improper routing design of the rear-view mirror electrical wiring allows rainwater that enters the door interior to accumulate on the connector terminals. This causes corrosion to develop on the connector terminals, increasing …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.