The stud bolt that secures the battery cable terminal to the engine compartment bulkhead has an improperly torqued nut. Vibration during operation can cause the nut to loosen, resulting in poor contact …
Bentley Continental GT 2010–2014
Bentley Continental GTC 2010–2014
Bentley Continental GTC V8 2010–2014
Bentley Continental GT Speed 2010–2014
Bentley Continental GT V8 2010–2014
+11 more
In the shovel loader engine, improper design of the governor linkage plate causes contact between the governor linkage plate and governor cable attachment point during accelerator operation, resulting in excessive bending of …
キャタピラー 901C 2013–2014
The parking control lever, which actuates the automatic transmission parking mechanism (a mechanism that mechanically locks the transmission output shaft), has insufficient welding process control. When the shift lever is moved to …
Mitsubishi eK WAGON 2008–2012
Mitsubishi i 2008–2012
Mitsubishi Toppo 2008–2012
Nissan Otti 2008–2012
During engine side mount installation work, the insulation of electrical wiring (engine room wire harness) has been damaged by tightening bolts. As a result, if the wire insulation breaks due to vibration …
Honda Civic 2009
The engine control unit has EU6 emission control software incorrectly programmed, resulting in non-compliance with NOx emission limits.
Mercedes-Benz CLS220 BlueTEC 2015
Mercedes-Benz CLS220 BlueTEC Shooting Brake 2015
The fuel filter drain plug mounting surface is not adequately flat. When the drain plug is tightened with excessive torque during manufacturing, the gasket may deform or develop compression cracks. Continued use …
Mazda CX-3 2014–2015
Mazda Demio 2014–2015
Engine accessory belts may have reduced strength due to uneven core wire tension during manufacturing. This can cause belt breakage under engine load, resulting in alternator and water pump failure, illumination of …
Mazda CX-3 2014–2015
Mazda Demio 2014–2015
The internal noise-suppression resistor structure in the ignition coil is inadequate. During sustained driving at constant vehicle speed, repeated heavy accelerator pedal operation can cause arc discharge at ignition, leading to disconnection …
Honda N-WGN CUSTOM 2014
The internal noise-suppression resistor structure in the ignition coil is inadequate. Arc discharge during ignition can cause fracturing at the resistor terminals. Continued use results in plug seal degradation and discharge, leading …
Honda N-ONE 2014
The structure of the noise-suppression resistor that removes electrical noise inside the ignition coil is inappropriate. Arc discharge caused by current flow during ignition may sever the resistor terminal. This can result …
Honda N-WGN 2014
Honda Fit 2014
In the forward collision mitigation system (collision mitigation brake system), improper management of repair parts for the adaptive cruise control unit has resulted in some vehicles being assembled with obsolete parts. Consequently, …
Honda Accord Hybrid 2013–2014
In entry doors (entrance doors) of living spaces in camper vehicles and similar applications, improper door lock mechanism design causes excessive load on resin components within the door latch during door closure. …
Isuzu Elf 2013–2015
Toyota Coaster 2013–2015
Toyota Dyna/Double Tire 2013–2015
Toyota Toyoace/Double Tire 2013–2015
Large-size transit buses equipped with a voice synthesis door open/close warning device have improper electrical wiring in the side switch box on the right side of the driver's seat. As a result, …
Mitsubishi Fuso Aero Star 2014–2015
The inflator (inflation device) of the front passenger single-stage deployment control airbag may rupture and scatter upon airbag deployment, potentially causing fire or passenger injury.
Toyota Alphard G 2004–2008
Toyota Alphard V 2004–2008
Toyota Vitz 2004–2008
Toyota Voxy 2004–2008
Toyota Noah 2004–2008
In the steering apparatus of the forklift, the kingpin design is inadequate, causing stress concentration at the kingpin notch, which may result in cracking. If operation continues in this condition, the crack …
T C M MR420 2005–2013
T C M MR450 2005–2013
Front seat belt pretensioners and seat belt anchors are improperly installed. In the worst case, the seat belt may detach and fail to restrain occupants.
Tesla Model S 2014–2015
The front right seat belt retractor may lock in low ambient temperatures due to improper manufacturing of retractor component parts. This prevents the seat belt from being withdrawn, potentially preventing occupants from …
BMW BMW 218d Gran Tourer 2014–2015
BMW BMW 218i Active Tourer 2014–2015
BMW BMW 220i Gran Tourer 2014–2015
BMW BMW 225i xDrive Active Tourer 2014–2015
In medium-duty dump truck and mixer specifications, the front underride protection device bracket has an improper shape. When the steering wheel is turned right, the pitman arm and drag link boot may …
Isuzu Forward 2014–2015
In the continuously variable transmission hydraulic clutch mechanism, the dimensional accuracy of the annular seal section that maintains hydraulic pressure is inadequate, causing the seal to be installed in an eccentric state …
Toyota Allion 2006–2008
Toyota ist 2006–2008
Toyota Auris 2006–2008
Toyota Corolla Axio 2006–2008
Toyota Corolla Fielder 2006–2008
+2 more
In hybrid vehicle fuel pumps, improper pump motor speed settings cause motor brush vibration, leading to premature wear. This activates warning lights, prevents fuel supply, disables engine operation, and may result in …
Lexus HS 250h 2009–2013
Toyota SAI 2009–2013
In the engine fuel line (delivery pipe), the fastening tool for the fuel pressure sensor is inappropriate, causing interference with adjacent components during fastening and resulting in insufficient fastening force. This may …
Toyota Isis 2009
In the battery unit for the work device of aerial work platforms, improper design of the vehicle battery charging control circuit can cause electrical noise immediately after charging stops. This may damage …
Hino Hino Dutro 2014
Isuzu Elf 2014
Toyota Dyna 2014
The vent hose that regulates pressure within the fuel tank has an inadequate design. When engine heat increases fuel tank pressure, fuel may leak from the vent hose. Leaking fuel can flow …
KTM FREERIDE 250 R 2012–2015
KTM FREERIDE 350 2012–2015
In vehicles modified for dual fuel operation (natural gas/gasoline), the CNG fuel control program is inadequate, potentially causing insufficient fuel supply. This may cause the engine control computer to enter safe mode, …
Daihatsu Mira 2012–2015
In vehicles modified for dual natural gas/gasoline operation, improper fuel filter mounting position causes the filter element to be pulverized by engine vibration. Continued use allows powder to clog the CNG injector, …
Daihatsu Mira 2012–2015
In vehicles modified to dual-fuel (natural gas/gasoline) configuration, the CNG injector assembly bracket and fuel filter bracket are secured with improper attachment methods. Engine resonance causes excessive load on the cable mounting …
Daihatsu Mira 2012–2015
In the prime mover of combine harvesters, due to inappropriate engine control unit programming, when engine output torque is low at high output RPM, unburned fuel concentration in exhaust gas increases. This …
ヰセキ HFR450G 2015
ヰセキ HFR463G 2015
In agricultural tractor engines, exhaust pressure in some units exceeds the range approved during type designation of the exhaust pressure control device for carbon monoxide and other emission prevention. As a result, …
ヰセキ NT543 2015
ヰセキ NT603 2015
ヰセキ NTA543 2015
ヰセキ NTA543C 2015
ヰセキ NTA603 2015
+1 more
On vehicles equipped with paddle shifters, due to improper engine control unit (ECU) programming, high loads may be applied to the drive pulley shaft of the continuously variable transmission when downshifting from …
Honda N-BOX 2011–2014
Honda N-BOX+ 2011–2014
Honda N-BOX Custom 2011–2014
Honda N-BOX+ Custom 2011–2014
Honda N ONE 2011–2014
In the tie-down device of a semi-trailer, improper manufacturing control of floor-mounted draw-type hooks has resulted in some units where the welds between the hook and stopper remain as tack welds only. …
フルハーフ - 2015