Before you buy, check it isn't under a dangerous recall.

The wiring connecting the cam position sensor from the fuse box is lengthy, resulting in high electrical resistance. During eco-start operation, voltage drop may occur in the power supply from the eco-start …

Some front drive shafts have insufficient durability due to improper machining of the inner race in the wheel-side joint. Continued use may cause the inner race teeth to wear under repeated acceleration, …

In the front seat belt retractor mechanism, there are units with reversed left-right assembly at manufacturing. As a result, the impact-sensing sensor may not operate correctly, and in worst-case scenarios, the seat …

The engine control unit contains an inadequate control program for the moment immediately before vehicle stop. When transitioning from fuel cut mode during deceleration to idling, the air-fuel mixture may become lean. …

Ignition coils for turbocharged engines lack sufficient durability. Internal elements may fracture due to repeated thermal stress from electrical current, causing the ignition coil to fail ignition, resulting in engine misfire and …

In forklifts, the LPG tank bracket design is inadequate. When performing inspections on the LPG tank by rotating the knurled bolt to swing the bracket laterally, the rear reflector on one side …

Improper manufacturing of the center pillar reinforcement has resulted in some vehicles containing parts with cracks. This may cause non-compliance with the side-impact safety standard specified in Safety Standard Article 18.

In the rectifier, inadequate moisture control during power module (power integrated component) manufacturing can cause adhesion failure between the finned case and power module after prolonged idling followed by sustained high engine …

In articulated bus steering systems, the steering column structure is inadequate such that when the steering is adjusted to the lowest position, the steering column and tilt mechanism components may interfere with …

In side curtain airbags, improper manufacturing processes have resulted in some airbags not being properly stored. Consequently, these airbags may not deploy properly during collision or similar events, potentially failing to provide …

Diaphragm degradation and other issues in spring chambers used beyond their replacement limit can cause air leaks. This results in reduced air pressure in the brake system, activating the parking brake and …

In certain passenger-side airbag inflators, the container may rupture due to internal pressure during airbag deployment, causing component fragments to scatter and potentially injure occupants.

In the forklift fuel system, improper fuel line design can cause air bubbles to form within the fuel lines. When the engine is off, these bubbles may coalesce to form air pockets. …

In plug-in hybrid vehicles, the high-voltage onboard charging control unit may incorrectly detect charging cable connection due to improper circuit board manufacturing. This may prevent charging when the cable is connected, and …

Certain connection flanges linking the propeller shaft to the differential gear lack sufficient lubricating grease in the flange's movable sections. Continued operation in this condition risks damage to the connection flange, and …

In the brake pedal of the braking system, the outer diameter of the brake pedal bearing shaft is slightly larger than the inner diameter of the brake pedal shaft bearing, which may …

On the vehicle's left rear seat, improper installation of the bracket for securing an ISOFIX child seat may prevent the child seat from being installed.

The coating on fuel line connection points has been applied improperly. During assembly, the coating may peel off at connection joints, resulting in poor sealing. This can cause minute quantities of fuel …

On agricultural chemical spray vehicles, improper routing of the exhaust pipe causes it to repeatedly receive vibration from the engine. This can result in cracks forming at the exhaust pipe mounting bracket …

In large tour buses equipped with optional passenger seats, the fasteners securing the seat covering are inappropriately selected. When thin-padded areas of the cushion are pressed firmly, the fasteners may penetrate the …

The starter magnetic switch in the engine starter device has improper sealant filling for waterproofing. Sealant can penetrate into the fuse terminal inside the magnetic switch. During use, the sealant softens and …

In the engine starting device, improper filling of waterproof sealant in the starter magnetic switch allows sealant to intrude into the terminal interior of the fuse mounting section. During use, the intruded …

The bank angle sensor harness attachment method in the engine cut-off device (bank angle sensor) that operates during tipping, and for vehicles not equipped with anti-lock braking system (ABS), the joint connector …

The battery ground terminal is fixed in an improper position, which may cause increased electrical resistance at the ground terminal during use. Continued operation in this condition could result in starter motor …

Improper wire harness routing design causes interference with the fuel tank rear surface. Continued operation may result in harness insulation abrasion due to vibration during driving, leading to short circuits, engine malfunction, …

The connector structure joining the ignition switch lead wire and wire harness in the starting system is inadequate. During use, terminals inside the connector may corrode due to water ingress. Continued use …

In the engine, improper heat treatment of tappets and cylinder head assembly processes have been identified. Consequently, if foreign material enters between the tappets and camshaft, the tappets will experience abnormal wear, …

In the headlight, due to improper manufacturing process of the bulb, incorrect material is used for the filament, resulting in some filaments with low rigidity. Continued use may cause the filament to …

Due to improper assembly instructions for the breather hose on the fuel tank, the hose may be installed in a kinked condition. This can cause hose blockage, preventing proper internal pressure regulation …

The transmission gearing has insufficient strength. During circuit driving or similar high-stress operation, performing gear shifts while rapidly opening the throttle fully can impose excessive stress on the affected gear. Continued use …