Before you buy, check it isn't under a dangerous recall.

The impeller (resin-molded rotor) in the low-pressure fuel pump may swell and deform due to improper molding conditions resulting in reduced resin density, causing the impeller to contact the pump cover. This …

In the electric servo brake system's brake operating simulator, improper manufacturing processes may allow assembly oil used during production to enter the pressure sensor. Consequently, the resistance element within the sensor may …

In the electric servo brake system's brake operating simulator, improper manufacturing processes may allow assembly oil used during production to enter the pressure sensor. This can cause corrosion of the resistor element …

The control computer (ECU) within the automatic transmission has improper welding management, resulting in welding defects at the ECU case joint surface. Continued use may allow transmission fluid to penetrate into the …

The control computer (ECU) in the automatic transmission has potential welding defects at the ECU case joint due to inadequate welder management. Continued use may allow transmission fluid to enter the case …

During factory completion inspection of vehicles, inspection of the emergency call device's voice call function was inappropriate, resulting in failure to properly conduct compliance inspection of the device against road transport vehicle …

The traction battery case bottom surface has insufficient corrosion protection. After prolonged use, rust can develop on the case, creating perforations. Water can then enter the battery case, causing short circuits that …

In the starter generator, due to improper manufacturing processes, the 48V cable is not properly bolted to the body ground point in the engine compartment. This may cause the engine start-stop system …

In the engine exhaust gas recirculation (EGR) system of shovel loaders, improper assembly procedures for the EGR valve—which regulates recirculated exhaust gas flow—may cause cracks to develop in the valve. Leakage of …

In shovel loader fuel piping, improper piping structure can cause excessive stress from work vibrations. Continued use may result in piping rupture and fuel leakage. In worst case, leaked fuel may contact …

High-voltage batteries may have incomplete sealing due to insufficient sealant application during manufacturing. When moisture ingresses into the battery, insulation resistance decreases, causing arc discharge. In the worst case, thermal battery abnormality …

In agricultural tractors, the steering control unit on the steering column may have insufficient stud bolt strength on the fixing bracket. Continued use may result in stud bolt fracture, causing the steering …

In the accelerator pedal of the agricultural tractor operator seat, due to inadequate quality of the accelerator sensor, the accelerator pedal movement may not be detected correctly. If use continues in this …

Certain high-voltage batteries have incomplete sealing due to insufficient sealant application during manufacturing. If moisture enters the battery, insulation resistance decreases, causing arcing. In worst-case scenarios, heat-induced battery abnormality may occur, potentially …

Anchor bolts securing the rear left and right seat belts were not properly tightened due to inadequate work instructions during repair operations. As a result, these bolts may loosen, and in the …

In de-icing agent spreader vehicles, water sprayers, and rotary snow removal vehicles, insufficient regulatory verification was conducted during optional equipment configuration. The rear identification plate reflector produces white light, which does not …

In welfare vehicles equipped with manual driving controls, the transfer board (a mechanism supporting wheelchair-to-driver-seat transfers) may rotate in an unintended direction when a passenger boards without deploying the board, causing their …

In large trucks and buses, severe operating conditions were difficult to identify, resulting in inadequate engine oil maintenance. Oil mist separator may become clogged by sludge accumulation (combustion deposits and degraded oil …

In vehicles modified to electric drive, control of the motor drive unit at high-speed rotation is inadequate. During re-acceleration at high speed, the control unit fail-safe function may activate, rendering the vehicle …

Due to improper on-vehicle tool loading specifications, the parking brake release tool (wrench) is not equipped. Consequently, if the parking brake remains engaged due to a malfunction or other issue, the tool …

Large and medium-sized tour buses lack the parking brake release tool (spanner) due to inadequate on-board tool installation instructions. Consequently, if the parking brake becomes stuck in the engaged position due to …

On large and medium-sized trucks and large and medium-sized tour buses, onboard tool specifications were inappropriate, resulting in the parking brake release tool (wrench) not being installed. Consequently, if the parking brake …

At the front pillar garnish mounting points, the waterproof durability of the mounting clips is insufficient. Over time, water intrusion into the cabin can occur, causing electrical connectors to become submerged and …

(1) In foot-operated parking brakes, the bolt fastening torque specification for securing the pedal to the body is inadequate, resulting in insufficient clamping force in some units. Consequently, the bolt may loosen …

The rear shock adjuster mount bolt lacks sufficient strength and may fracture due to vehicle vibration. This can cause the rear shock adjuster to detach and contact the rear tire, resulting in …

In the heating system component, the heater element within the heater module has insufficient durability. Repeated electrical cycles cause cracks in the sensor layer material coating, creating areas of poor electrical conductivity …

Small trucks and buses equipped with manual transmissions have defective reverse light switches installed. Continued use in this condition may result in failure to correctly detect reverse gear engagement, potentially causing the …

The subframe of bulk powder transport semi-trailers has inadequate structural design, which may cause cracks in subframe components. Continued use in this condition allows cracks to propagate, and in the worst case, …

On aerial work platforms, the mounting position of the rear combination lamp is inappropriate, which may result in the visibility range of the tail light and brake light not conforming to road …

On vehicle transport vehicles, the integrated rear combination lamp's rear reflector was installed without recognizing that the reflector position differed, resulting in the rear reflector mounting position not complying with road transport …