Before you buy, check it isn't under a dangerous recall.

In small rotary compactor trucks with wide-cab configuration, improper routing of wiring on the right side within the high-mount rear panel can cause contact with rear door-attached components during rear door opening …

In vehicles equipped with heated belt-in seats, the crimping process connecting the heater wire and power wire may be performed improperly, resulting in insufficient crimping of the heater and power wires. This …

The engine control unit has an inadequate control program for AdBlue injection system cooling. After high-temperature operation under heavy load followed by parking, AdBlue injection system cooling becomes insufficient, potentially causing clogging …

The bank angle sensor holder component molding process and die management are inadequate, resulting in insufficient seal integrity in some units. When water ingresses into the sensor during wet-weather riding, circuit board …

① The rear stop switch contains waterproof grommet material with improper formulation, resulting in insufficient durability. Ozone degradation can cause cracks in the grommet, allowing rainwater to enter the switch and accumulate …

Certain large trucks equipped with a PDM (Power Distribution Module: fuse and relay box) on the left side of the driver's seat have incorrectly routed positive power supply wiring to the PDM. …

Front drive shafts may have inadequate heat treatment during manufacturing, resulting in surface cracks on the outer race with insufficient strength. As cracks progress during use, the outer race may fracture, causing …

The EGR pressure sensor mounted on the exhaust gas recirculation (EGR) device has insufficient corrosion resistance to exhaust gases. Corrosion from exhaust gases can cause abnormal sensor output, resulting in warning light …

During the manufacturing process of the inhibitor switch that detects shift range position, the replacement criteria for the welding fixture were inadequate, resulting in insufficient welding and inadequate sealing. As a result, …

In vehicles equipped with Vehicle Master Control Unit 2 (VMCU2), the program that performs calculations and operational diagnostics based on the accelerator pedal opening signal contains a calculation formula error. This may …

The engine control module software contains a defect that may prevent proper diagnosis of catalytic converter malfunction. As a result, if a catalytic converter fault occurs, the warning light may not illuminate, …

Due to incorrect program settings in the body control module, an emergency brake display light not configured for Japanese specifications activates, causing the brake lights and auxiliary brake lights to flash. This …

The fuel pump impeller (resin-molded rotor blade) may have low resin density due to improper molding conditions, causing it to swell and deform when exposed to fuel. This can cause the impeller …

The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to inappropriate molding conditions that reduce resin density, causing exposure to fuel. This can cause the impeller …

The threaded hole machining is improper at the mounting location of the towing eye bolt on the front cross member, preventing the eye bolt from being installed to the required depth in …

In the trunk room ground wiring, improper tightening during manufacturing has resulted in the insulator being pinched and clamped to the stud bolt. This can cause loosening during use, leading to wire …

Certain daytime running lamps have improper software, resulting in brightness below the required standard. These do not comply with the safety standards specified in Safety Standards Article 34-3.

In the forward/reverse control electromagnetic valve (shuttle valve) of agricultural tractors, due to the following conditions, malfunction of the detection switch causes an error to be detected, and the fail-safe function may …

In the forward/reverse control solenoid valve (shuttle valve) of agricultural tractors, the following conditions may cause detection switch malfunction, resulting in error detection and fail-safe shutdown. Continued operation may progressively increase error …

Bolts and nuts fastening electrical system components and steering system components, as indicated in non-conforming areas ① and ② below, have inadequate quality control resulting in insufficient tightening in some cases. Continued …

Certain tail lamps have improper assembly, causing strong interference with the tailgate panel. This can damage the tail lamp housing, allowing rainwater and other liquids to enter the lamp interior. In the …

Position lamps/daytime running lamps have defective LED circuits due to inadequate manufacturing control. Circuit discontinuity may occur during use, causing position lamps/daytime running lamps to fail to illuminate.

In the hybrid system inverter, improper assembly of the high-voltage cable connector cover allows moisture to enter the transmission inverter section, creating risk of short circuit. This causes the engine warning light …

The fastening screws securing the front bumper clips to the left headlamp may not be properly fastened due to inappropriate torque settings during assembly, which can cause looseness in the front bumper. …

During engine assembly, bolts fastening the water pipe to the engine may be insufficiently tightened. Continued operation in this condition may result in bolt detachment and coolant leakage, potentially contacting the exhaust …

(5) In the view monitor unit, due to inappropriate system processing conditions, memory may not reset upon restart. This can cause image processing to slow due to insufficient memory, resulting in distorted …

The view monitor unit may fail to activate the side and back camera switching system at startup due to improper system activation conditions. This causes the i-ACTIVSENSE warning light to illuminate and …

The fail-safe activation conditions in the electric drive control computer are inappropriate. When a plug-in hybrid inverter cooling malfunction occurs, even if motor operation is restricted, the inverter may overheat. Continued use …

The engine control computer has improper fault determination conditions. When idle stop shuts down the engine and engine shutdown is interrupted by accelerator operation or similar, the computer may temporarily fail to …

In the engine control computer, due to inappropriate hybrid system activation conditions, if the push-button start is turned off and then turned back on for restart approximately 8 seconds later, the mild …