Before you buy, check it isn't under a dangerous recall.

In the diesel engine particulate filter (DPF), improper shape of the internal buffer material may cause the ceramic filter to overheat and crack. This can result in degraded particulate matter filtration performance …

A defect in the body control module software causes a delay of several seconds in the automatic activation of low-beam headlamps during situations requiring automatic low-beam engagement, such as in tunnels. This …

The warning triangle may not meet the technical standard for reflective performance due to inadequate manufacturing control.

In agricultural tractors, the main harness routing is improperly installed, causing contact with the DPF in some units. Continued operation in this condition risks harness damage, potentially resulting in loss of power …

In the running gear of agricultural tractors, improper paint processing results in insufficient wheel coating hardness in some units. Consequently, wheel mounting bolts and nuts may loosen.

In the integrated brake unit, improper manufacturing control has resulted in foreign material adhesion on the motor sensor circuit board. This causes electrical contact failure, resulting in brake warning light illumination and …

In battery-powered forklifts equipped with heaters, improper insertion procedures for the heater power harness connector have resulted in some units being inserted with terminal orientation reversed. This causes terminals to fail to …

In wheel crane seats, improper assembly work of the seat adjuster results in insufficient bolt torque in some units. Continued use in this condition may cause bolts to loosen due to traveling …

In articulated buses, the glass fitted to the destination display on the vehicle front is adhered using an improper method. The adhesive may separate during use, and in the worst case, the …

The seal gasket used at the connection of the rear axle shaft has inadequate design. Under conditions of severe fluctuating driving torque, the seal gasket may shift slightly in the rotational direction …

On large and medium-duty trucks, the attachment bolts of the cab bottom bracket are insufficiently tightened. Continued operation in this condition may result in bolt loosening and detachment. Note: The cab bottom …

The bolt hole drilling depth in the cable fastening section within the steering wheel was inappropriate, causing improper cable crimping in some vehicles when bolts are tightened. This results in poor electrical …

Front suspension top caps on certain units have inadequate fastening due to improper manufacturing. Continued use may result in top cap detachment due to driving vibration, leading to suspension malfunction and loss …

Replacement repair kits for rear shock absorbers were incorrectly packaged with bolts shorter than the genuine specification. If these incorrect bolts are used during replacement, vibration during driving may cause loosening, resulting …

In the front brake, due to improper brake fluid filling procedure, a small amount of air bubbles may be present in the brake hydraulic system. If operation continues in this condition, when …

In the fuel system, improper assembly procedures have resulted in insufficient crimping of the single-ear hose clamp connecting the fuel hose to the fuel pump. Consequently, when high fuel pressure is applied, …

Due to inadequate work instructions in the spark plug assembly process, spark plugs may be damaged. As a result, spark plugs may misfire at low RPM, potentially causing unstable idling, hesitation during …

In the electric power steering system, improper work instructions during vehicle assembly at the factory caused contact between the body and internal components during assembly. As a result, internal electronic components may …

The ground wire terminal nut of the 12V battery located beneath the passenger seat may not be tightened to specification due to improper assembly during manufacturing. Vibration during driving can cause the …

Roof panels adhesively attached to the vehicle body may not have been repaired with adequate adhesive strength due to improper repair work instructions during service. This can result in progressive delamination from …

The fuel pump impeller (resin-made rotor blade) may swell and deform due to improper manufacturing when exposed to fuel. This causes the impeller to contact the pump housing, resulting in fuel pump …

In electric small trucks, due to improper VCU control programming, a communication error is mistakenly detected, causing the high-voltage system to shut down for safety reasons. As a result, the driver may …

In electric mini trucks, due to inappropriate control software in the EPB ECU, if the EPB release operation is performed during EV system startup triggered by key-on, the EPB and Hill Start …

High-voltage battery cell modules have been manufactured with improper tolerance settings, resulting in some cell modules with excessive tolerances. Under specific conditions, this can cause irregularities in charge-discharge characteristics. When affected cell …

Improper assembly control at the manufacturing plant resulted in wheel housing extensions (fender flaps) not being installed on the vehicle body. Due to assembly tolerances, tires may protrude beyond the body, potentially …

The rear combination lamp mounting bracket on swap body container carriers has insufficient strength due to inadequate vibration analysis. Running vibration may cause cracks in the mounting bracket, and in the worst …

The fuel pump impeller uses an inappropriate material, which can expand and deform due to fuel temperature. This causes excessive friction between components, resulting in fuel pump malfunction, and in the worst …

The Engine Control Unit (ECU) has improper program settings, causing the speedometer to display incorrect speed until engine rpm exceeds a certain threshold. This may prevent the driver from accurately perceiving vehicle …

①The engine control unit (ECU) was programmed with non-specification firmware, causing the fuel evaporative emission control function to malfunction. As a result, fuel vapors are not drawn into the intake system, and …

The control unit governing the retractable rear spoiler contains improper programming, causing the rear spoiler to rise higher than the specified maximum height. This causes the rear spoiler to obstruct the high-mounted …