Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 37 of 355
Some agricultural chemical sprayer vehicles have propeller shafts with insufficient fastening bolt torque. Continued use in this condition may result in propeller shaft detachment and loss of vehicle mobility.
In the speed adjustment control device (HST lever) of agricultural chemical spraying vehicles, inadequate internal lubrication causes the HST lever to tilt toward the forward position when returned to neutral. This may …
The mounting bracket for the refrigeration unit condenser, installed between the wheelbase of large refrigerated trucks, has insufficient design consideration, which can cause cracks at fastened joints. Cracks may propagate due to …
The seat position fixing component welds on the driver and front passenger seat position adjustment frames were improperly executed, resulting in insufficient weld strength in some units. When the weld joint of …
In the front blower motor of the air conditioning system, improper securing of the brush holder can cause the brush spring to disengage and the brush to short-circuit against the motor case. …
The instrument cluster glass has insufficient impact resistance design against side collisions. In severe crash events, the glass may shatter and scatter fine fragments toward the driver's seat, potentially causing injury to …
The O-ring in the turbo inlet pipe may be installed twisted due to inadequate control of the component manufacturing equipment. This can cause O-ring damage and oil leakage, resulting in a low …
In large-capacity route buses, the connector terminal arrangement of the electric water pump for cooling the urea water injection unit is improper. When the DPF is at high temperature immediately after engine …
In small truck refrigeration unit-equipped vehicles, the idler pulley fastening section shape is inappropriate, causing excessive stress on the idler pulley bolt due to belt tension, which may cause fracture. As a …
On large-capacity intercity buses equipped with EZGO/CB (mid-door open stopping assist device), the electrical circuit of the EZGO brake valve is improperly designed. When the mid-door is opened immediately before stopping, the …
Exhaust pipe connection clamps may be insufficiently tightened due to improper manufacturing process. This can result in pipe connection separation causing abnormal noise and exhaust gas leakage into the cabin. In worst …
The engine control unit has inadequate software, resulting in excessively high engine speed settings in safe mode when an accelerator pedal malfunction is detected. When this safe mode activates, unintended acceleration may …
In the transmission (Dualogic), some vehicles have damage to the oil reservoir tank hose connector resulting from improper manufacturing processes. This may cause oil leakage, illumination of warning lights, and the gear …
In the mechanical automatic transmission control computer of small hybrid trucks, due to inappropriate control programming for the automatic clutch actuation motor and improper motor replacement timing settings, when the motor is …
In the mechanical automatic transmission control computer of small hybrid trucks, the control program for the automatic clutch actuator motor and the motor replacement timing setting are inappropriate. When the motor is …
The high-pressure fuel pump has insufficient design consideration, resulting in inadequate strength after press-fitting of component assemblies. During use, internal pump wear and damage may occur. This can cause stress concentration at …
In rear seat belt retractor mechanisms, improper manufacturing control of internal components resulted in some units being assembled with shafts of incorrect specifications. Consequently, when a force limiter activates during a collision …
Due to improper production instructions, some vehicles designated for cold-weather specification were assembled with standard-specification wiper motors and wiper linkages. Depending on snow accumulation conditions, this may result in inadequate wiping performance.
The impeller (resin fan wheel) of the low-pressure fuel pump replacement part may have reduced resin density due to improper molding conditions, causing it to swell and deform when exposed to fuel. …
The control program for the lane-keeping assist function (part of the adaptive cruise assist system) contains deficiencies due to insufficient evaluation during development. As a result, the system deactivation operation upon steering …
Due to improper software in the engine control unit, when an AdBlue injection pressure abnormality is detected, AdBlue injection is stopped but the warning light does not illuminate. This may cause the …
The left tail lamp has insufficient welding at the joint between the body and lens, creating a risk of separation. This could allow rainwater to enter the lamp interior, causing circuit short-circuit …
In the vehicle cabin fuse holder, inadequate manufacturing process control has resulted in improper installation of the power supply connector on some fuse holders. Loosening of this connector may affect various vehicle …
The rear spoiler fastening bolts have improper length, which may cause the mounting bolts connecting the bracket (fixed to the vehicle body mounting bracket) and rear spoiler to loosen during use, and …
The design of the MAP sensor (intake manifold absolute pressure sensor) hose in the engine management system is inadequate, which may prevent correct measurement of intake air pressure. This can cause malfunction …
In agricultural tractor shift levers, internal components are improperly designed. When the lever is operated forcefully to its end position in low-speed ranges (0–2 km/h), incorrect drive commands may be recognized. Consequently, …
The fuel supply module flange in the fuel tank of the fuel system has improper component design. When ambient temperature is high and low-quality fuel is used, excessive current flow can cause …
The instrument cluster program for the brake booster warning system is inadequate. When the brake booster malfunctions, the warning light does not illuminate. After the warning message is displayed, an incorrect warning …
The tail lamps installed on the lower rear of large wing-body vehicles do not meet safety standards for mounting position. Due to insufficient design review, the distance from the vehicle's outermost edge …
In the rear combination lamp, the tail light LED may be damaged during manufacturing. During vehicle use, the damaged area may break, causing the tail light to fail to illuminate.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.