Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10558 recalls on record · page 38 of 352
The current rectification module in the voltage conversion device (DC-DC converter) has an improper internal component structure. When the module fails during use due to manufacturing variations and other factors, a short …
In the hydraulic hose for wing door opening and closing operations on wing-type vehicles, there were deficiencies in the management of manufacturing fixtures, resulting in some terminal fittings attached to the hose …
On vehicles equipped with front air suspension, the anchor bolts securing the air spring on the front axle have been tightened to improper torque specifications. Due to running vibration and other factors, …
The noise label contains insufficient review of its contents, resulting in incorrect values for proximate exhaust noise, acceleration run noise, and average vehicle speed at the start of wide-open throttle acceleration. As …
(1) Following amendments to road transport vehicle safety standards, the turn signal indicator's turn unit was designed incorrectly, resulting in the failure to display a warning to the driver when the turn …
In the braking system, the front brake hose attachment to the vehicle body may be improperly installed and not positioned correctly. Consequently, the hose may contact the hose guide edge, and continued …
In route-specification large buses, the harness within the distribution box installed on the upper right side of the driver's seat interferes with the rear upper edge of the air conditioning control unit …
The onboard supply control unit contains a software defect due to insufficient verification during software design. Consequently, when only the driver is seated and the luggage compartment is loaded with heavy cargo, …
The control program for the lane guidance function of the driving assistance system (part of the adaptive cruise assist system) contains defects due to insufficient evaluation during development. Consequently, the system disengagement …
The collision mitigation brake in the driver assistance system has control programming that causes it to react overly sensitively in certain situations, which may result in the system misidentifying roadside structures and …
The trim attachment on the upper portions of the left and right seats on the first floor has inadequate design. During vehicle operation, vibrations may cause the trim attachment to loosen, creating …
The bolts securing the center beam to the frame underwent a surface treatment change during manufacturing, reducing friction in the threaded section. Consequently, when tightened to the same torque specification, the clamping …
In the engine, the right-side crankcase cover has improper manufacturing process, causing paint adhesion on the sealing plug press-fit section. Due to engine heat, the sealing plug retention force decreases, and continued …
The control program for the driving assistance system Travel Assist has deficiencies due to insufficient evaluation during development. Consequently, the system deactivation operation upon steering hand-off detection does not comply with safety …
In passenger doors, improper manufacturing control of the outer door handle may result in the membrane filter not being correctly installed. Moisture can subsequently penetrate the electronic circuit, potentially causing unintended door …
The strut mount on the front suspension may be deformed due to inadequate equipment management during the press-nut manufacturing process. As a result, some bolt connections between the vehicle body and strut …
Due to improper design between the driver's seat and the interior trim behind it, when the driver's seat is lowered to its rearmost position during entry and exit, the cover of the …
In the fuel system, insufficient corrosion resistance evaluation at the design stage has led to galvanic corrosion between dissimilar metals: the fuel pipe (aluminum) between the left and right fuel tanks and …
Due to inadequate process control during front wheel assembly, certain bolts and nuts may have insufficient fastening torque. Consequently, these fasteners may loosen under running vibration, potentially causing abnormal noise, decreased running …
The bracket securing the monitor installed near the upper deck stairwell and the upper cargo shelf has an improper design. Vibration during operation may loosen the bracket's fixation. In the worst case, …
In vehicles where the Body Domain Controller (BDC) has been replaced, work is completed without initializing vehicle data due to inadequate work instructions. As a result, the speed-dependent automatic door lock function …
In vehicles equipped with a height lowering device for parking operations, the control circuit design is inadequate, therefore
In vehicles equipped with a ride height lowering device for parking operations, the control circuit design is inadequate, resulting in
① The rear brake lamp switch has an inadequate seal design. Foreign matter entering through the seal can accumulate on electrical components and cause corrosion over time, potentially causing the switch to …
In headlights, when used for extended periods beyond design specifications such as in taxi service, the aluminum coating on the reflector may peel due to heat and ultraviolet radiation from the bulb. …
The lower arm ball joint attachment in the front suspension assembly has been manufactured improperly, causing cracks in some units. Repeated driving over rough road surfaces causes these cracks to propagate, and …
The waterproof cap for the rear door has not been installed due to improper work instructions. High-pressure washing and similar operations may cause water ingress to the electrical wiring. Continued use in …
The camera for the preventive safety function (Smart Assist) is affixed to the windshield glass via a bracket. Inadequate adhesive process control results in weak adhesion on some units. During use, the …
In the front fog light (front LED fog lamp), inadequate process control has resulted in insufficient solder application to the LED chip. Continued use in this condition may cause solder detachment, resulting …
The center bearing bracket connecting the drive shaft that powers the cargo handling pump of a tank vehicle mid-span has unwelded sections due to inadequate work instructions. This results in insufficient weld …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.