Before you buy, check it isn't under a dangerous recall.

The seal at the boot attachment point of the steering gear is inadequate, and the air conditioning drain hose is positioned directly above it. As a result, air conditioning condensation may drip …

In combine harvesters, due to inadequate insulation treatment of the exhaust pipe and its vicinity, as well as improper design, chaff accumulates near the exhaust pipe. During diesel particulate filter (DPF) regeneration …

The driver's seat belt retractor may be improperly manufactured, causing the seat belt to fail to lock during hard braking or similar conditions. As a result, the seat belt may not restrain …

On certain wheel loader cab configurations, rental company vehicle management number stickers are affixed to the side windows. This may result in non-compliance with Safety Standard Article 29 (window glass requirements).

In engines of large trucks and buses, manufacturing variations in the oil pump can cause the pump gear shaft to tilt. This results in gear tooth wear, and continued operation in this …

(1) In the power transmission system, an improper pin selection was made for connecting the primary transmission rod linked to the primary transmission lever with the traveling HST (hydrostatic continuously variable transmission), …

(1) In the power transmission system, the pin connecting the main transmission rod (linked to the main transmission lever) and the HST (hydrostatic continuously variable transmission) was selected inappropriately and connected with …

In leaf suspension variant vehicles, the automatic headlamp leveling control program in the vehicle master control unit is inadequate, causing the headlamp aiming adjustment device to not operate when the lighting switch …

In the braking system of large and medium-duty trucks, the resin piston material in the parking brake relay valve is inappropriate, causing hydrolysis due to moisture in the air circuit. The piston …

On large and medium-duty trucks, due to inadequate speedometer control programming, performing specific key operations under certain conditions during program startup may cause warning lights to illuminate and the speedometer and related …

In the dashboard, due to improper manufacturing processes, the passenger airbag aperture may not be correctly machined. As a result, the airbag may not fully deploy upon collision, potentially causing excessive injury …

In diesel engines, improper manufacturing control of the timing chain resulted in the use of components without surface treatment. Consequently, the timing chain may stretch during use, causing abnormal noise from the …

In diesel engines, improper manufacturing control of timing chains resulted in the use of components without surface treatment. During use, timing chain elongation causes abnormal engine noise, and in worst-case scenarios, valve …

In the fuel system of engine-powered forklifts, some injector bodies have insufficient strength due to improper process control during molding. Consequently, repeated common rail pressure (fuel pressure) cycles may cause cracks to …

In the damper assembly, the nut securing the rear suspension arm is made of inappropriate material, which in some cases causes premature corrosion cracking. This results in loosening of the arm attachment …

In internal combustion forklifts, the oil seal of the brake master cylinder may have insufficient sealing performance, causing brake boost oil to flow into the brake oil side. Additionally, under frequent brake …

In counterbalance battery forklifts, the bracket shape of the battery disconnect mechanism is improper, resulting in insufficient clearance between the battery disconnect lever and bracket. When the battery hood deflects, this clearance …

On agricultural tractor brake hoses, improper assembly instructions for adjacent hose clamps result in interference with clamps. Continued operation in this condition may cause hose damage due to running vibration and engine …

Agricultural tractor crankshaft bearing cap bolts may have insufficient fastening torque due to improper programming of the tightening tool. Continued operation in this condition can cause bolts to loosen due to engine …

In the power transmission system of agricultural tractors, the PTA controller (transmission travel control device) seal surfaces were improperly cleaned, resulting in insufficient seal performance in some units. Water may consequently ingress …

The body control module has an inappropriate control program. When the light switch is operated to the parking light position while the adaptive driving headlight is ON and the fog light is …

Engine mount bracket attachment bolts are susceptible to loosening due to improper installation. Continued operation may result in bolt fracture, causing the engine to tilt and interfere with the front suspension member, …

The seat belt upper anchor bolts on the driver and front passenger seats have insufficient clamping torque due to improper tightening during assembly. This can cause the bolts to loosen upon collision …

Brake calipers on the front and rear wheels have insufficient fastening torque on their mounting bolts due to improper tightening during assembly. Consequently, the bolts may loosen due to driving vibrations, and …

In the engine manufacturing process of large trucks, fasteners (bolts or nuts) for engine accessories may be inadequately tightened. Vibration and other factors can cause these fasteners to loosen during use. Continued …

The control display for front passenger seat adjustment, operable from the rear seat, has a defective control program. When the touchscreen is operated while water droplets or similar substances are present on …

Ignition coils may have been incorrectly installed or inadequately secured due to improper assembly procedures. This can result in cylinder misfire on affected units, causing reduced engine output and illumination of the …

Front left and right wheel arch covers may not be properly secured due to improper assembly during manufacturing. This can cause the covers to lift and become detached, and in the worst …

Due to improper manufacturing instructions for the starter motor electrical wiring, the wiring is installed in a position where it interferes with the starter motor housing. As a result, the wiring insulation …

The side spoiler on the upper tailgate may not be properly secured due to inadequate assembly during manufacturing. This can cause separation and loosening of the fastening, which in the worst case …