Before you buy, check it isn't under a dangerous recall.

Due to improper manufacturing instructions for the starter motor electrical wiring, the wiring is installed in a position where it interferes with the starter motor housing. As a result, the wiring insulation …

The side spoiler on the upper tailgate may not be properly secured due to inadequate assembly during manufacturing. This can cause separation and loosening of the fastening, which in the worst case …

The air conditioning evaporator drain hose assembly may be improperly installed, allowing condensation water to leak into the passenger compartment. This can lead to flooding of the undercarriage, causing corrosion and short …

In the headlight automatic leveling unit, improper temperature management during soldering resulted in soldering at an insufficiently low set temperature. Consequently, solder joints may separate due to vibration during operation, causing loss …

The high-pressure fuel pump has improper welding at manufacture, causing welding metal particles to remain inside the pump and potentially obstructing the operation of the fuel pressure regulating valve. This may result …

In the diesel engine particulate filter (DPF), improper programming of the engine control unit may cause internal temperatures to exceed design specifications. This can result in thermal damage to the filter, causing …

On large trucks compliant with the 2016 emission regulations, the mounting position of the side marker lights is improper. Additionally, on vehicles equipped with automatic headlight function, the auto on/off program is …

Due to inadequate process control at the front seat assembly plant, the bolts securing the seat belt catch are not correctly installed on some units. This causes abnormal noise from the affected …

In the hybrid system, insufficient electrical noise immunity of the power conversion module control board causes the power control circuit to misidentify electrical noise generated by high-voltage circuit voltage fluctuations as abnormal, …

In the power transmission system of large trucks, improper bending in the center bearing bracket may cause cracks to develop due to propeller shaft rotational vibration. Continued operation can lead to bracket …

Some speedometers are assembled with non-specification needle retention pins. When instrument panel temperature rises, the coating on the retention pin surface becomes tacky, and in worst case the needle may adhere to …

Certain steering knuckles have reduced strength due to improper heat treatment during manufacturing. When subjected to large forces, they may deform and cause wheel alignment misalignment. Continued use in this condition may, …

The lithium-ion battery ground bolt attachment to the vehicle body is improperly secured, resulting in defective grounding in some units. Continued operation in this condition may result in failure to restart after …

The engine control unit (ECU) has an inappropriate control program that may delay vacuum supply from the engine to the brake booster under certain combined conditions. In the worst case, strong braking …

In the steering system, the steering yoke connection portion of the steering gearbox has an inappropriate shape, which may cause play (looseness) at this connection. Continued use in this condition may cause …

②The tire chain box mounting bracket attached to the rear of the tank semi-trailer frame has an improper structure, which may cause cracks to develop due to vibration during operation. If left …

The rear frame attached to the subframe of the tank semi-trailer has an improper structural design. Running vibrations and similar forces may cause cracks to develop at the rear frame attachment points …

The high-pressure fuel pump has insufficient pressure resistance in its structural components relative to fuel pressure, causing internal wear and damage during use. This concentrates stress at pump weld points, potentially causing …

In the exhaust emission control device, NOx sensor wiring installed before and after the SCR catalyst may be reverse-connected due to improper assembly work. This may prevent the exhaust emission control device …

Transmission oil cooler hoses have insufficient strength due to improper manufacturing processes. During use, the hoses may rupture, causing oil to spray, and in worst cases, leading to fire.

In the tailgate open stay, the attachment structure between the lower ball joint and the vehicle body ball stud is inadequate, causing the clip that fixes the ball joint and ball stud …

In rear reflectors, improper process control during reflector molding has resulted in some units where the internal surface is not correctly formed. Consequently, reflected light may scatter, potentially failing to comply with …

In the body integrated control computer located in the fuse block of cold-weather specification vehicles, the brake light control circuit design is inadequate. Noise generated during wiper operation causes overcurrent to flow …

Some front left and right seatback covers have improper processing and do not meet flammability technical standards. As a result, in the event of a fire, flames may spread faster than specified …

The side stand mounting bracket has insufficient durability, which may cause deformation or breakage of the bracket. As a result, the bracket may deform while the vehicle is parked on the side …

Due to improper programming of the control unit in the dashboard panel insert, the seat belt warning light may illuminate only once or briefly and the warning chime may sound only once …

Due to an inappropriate firmware voltage threshold in the exhaust bypass valve actuator, the engine check lamp may illuminate based on alternator charging conditions, potentially limiting engine output in fail-safe mode.

1. In the rotary snow removal vehicle electrical wiring, improper wiring routing instructions cause wiring to contact covers, risking insulation damage from vibration during operation. This may result in short circuits and …

1. In rotary snow removal vehicles, improper routing instructions for electrical wiring can cause wiring to contact protective covers. Operating vibrations may damage the insulation, potentially causing short circuits, burning, and fire …

Certain agricultural tractor accelerator pedal return springs have improper manufacturing processes. The spring may fracture during tractor operation, causing the accelerator pedal to remain depressed even after the operator releases their foot, …