Before you buy, check it isn't under a dangerous recall.

Certain van-type heavy-duty trucks equipped with spare tire mounting devices installed between the wheelbase have inadequate structural design, resulting in insufficient strength of the mounting device. Consequently, vibration during operation may cause …

The Restraint Control Unit contains improper maintenance programming. When reprogrammed via diagnostic equipment during repair operations, the programming may complete in an error state. This causes the airbag deployment control threshold to …

On the gear change pedal, the fastening torque setting of the change pivot bolt that attaches the pedal to the vehicle body is inappropriate. During forceful upshift operations, this bolt may loosen. …

In some headlights, after the optical axis inspection process at the vehicle production facility, a gap adjustment was performed between the headlight and vehicle body (fender), but the optical axis was not …

The headlight optical axis may not satisfy safety standards because inspection and adjustment were performed while the vehicle production facility's optical axis inspection equipment was not operating normally.

In halogen-specification right-side headlights, inspection and adjustment were performed with improperly configured optical axis inspection equipment at the vehicle manufacturing facility, creating a risk that the optical axis may not meet safety …

In the main wire harness, improper cable routing causes the harness to contact frame protrusions when the steering is turned fully left or right. This can damage the harness insulation, causing internal …

In the fuel piping of wheel crane engines, improper assembly has resulted in inadequate clearance between the fuel piping and frame due to piping variation. Continued operation of affected vehicles with contact …

In the wheel crane engine fuel piping system, improper clearance between the frame and fuel lines may cause contact between the fuel piping and frame during engine startup vibrations and similar events. …

In the hydraulic steering circuit hose of wheel cranes, the fixing range of the hose protection material is inappropriate, which may cause localized bending stress. If operation continues in this condition, repeated …

In battery cables, due to inadequate design specifications, terminals are manufactured with incorrect material in some cases. This causes premature degradation, increased resistance values, heat generation at the terminal, and in worst …

Water pump belts may have been installed with damaged assembly tools due to inadequate maintenance of the assembly equipment. This can cause belt damage during installation. Continued use of a damaged belt …

The metal water supply tank for the toilet in large buses has insufficient strength in the tank mounting bracket, which can cause the bracket to be damaged and the tank to detach. …

The metal water supply tank for lavatories on large buses has insufficient strength in the tank mounting bracket, which can cause damage to the bracket and result in tank detachment. This can …

Due to improper manufacturing tolerances in the rear reflector, some units have mounting boss diameters smaller than specified. This can cause the clip securing the rear reflector to detach due to driving …

The exhaust brake control program in the engine control computer is defective, which may prevent the exhaust brake from engaging while descending slopes. This results in insufficient deceleration and violates Safety Standard …

Certain rear combination lamps have insufficient density in resin components due to inadequate production control of component materials. Continued use in this condition may cause the resin component to undergo thermal shrinkage, …

In the automatic clearance adjustment mechanism (strut set) for rear wheel brake shoes and drums, improper management of the grease application equipment during component assembly has resulted in insufficient grease coating on …

The optical axis adjustment program in the control unit for adaptive LED headlights is inappropriate. When the push-button start is pressed to turn the power position ON, the headlight optical axis initialization …

In the exhaust emission control system, improper production control during the catalytic converter assembly process has resulted in non-specification catalytic converters being installed in some vehicles. This causes a mismatch with engine …

The gas generant in the driver-side airbag inflator may degrade due to repeated environmental temperature and humidity fluctuations. As a result, the internal pressure in the inflator may abnormally rise during airbag …

The fuel tank mounting bracket lacks sufficient structural strength. Vibration during operation may cause cracks to develop near the mounting points. Continued use could allow cracks to propagate, causing fuel seepage, and …

The electric air conditioning compressor cover has insufficient corrosion resistance, allowing moisture to enter the compressor interior. If electrical leakage occurs inside the compressor, the EV warning light may illuminate and motor …

Washers used on the idler gear that drives the oil pump in agricultural tractors have improper heat treatment, causing premature wear in some units. As washers wear, play develops in the bushing. …

Certain bolts securing the water pump pulley on agricultural tractors have insufficient tightening torque. Operating vibrations can loosen these bolts, causing the pulley to misalign, resulting in abnormal noise and potential separation …

On agricultural tractor cooling water hoses, the clearance between the compressor belt and the hose is inadequate, such that when the belt stretches, it can interfere with the cooling water hose. Continued …

In diesel engines of heavy-duty trucks compliant with 2016 emissions regulations, improper program settings in the engine management system (EMS) may prevent diagnostic monitoring of fuel pressure control in the fuel system …

In the fuel pump of the shovel loader, demagnetization occurs at low temperatures due to improper selection of the permanent magnet inside the pump, causing the motor to operate at high speed …

The engine cooling system has an inadequate air-bleeding design. When refilling coolant after repairs, if the dedicated special tool is not used correctly, air may not be properly bled from the cooling …

The front wiper arm mounting nuts may loosen due to improper fastening torque specification design. This can result in reduced windshield wiping function and inability to maintain adequate visibility.