Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 26 of 175
The onboard diagnostic control program in the engine control computer (ECU) is improper. When fault diagnostic data processing overlaps, the data may become corrupted. This causes the ECU to detect an anomaly …
Due to inadequate manufacturing control of ICs (integrated circuits) in the engine controller, internal fractures may occur during use, potentially resulting in engine start failure or stalling while driving.
In dump trucks and similar vehicles, improper installation of backup lights and rear combination lamps results in backup lights, brake lights, tail lights, rear reflectors, and turn signal indicators not meeting the …
In some vehicles, the wiring for EBS (Electronic Braking System) communication and ABS malfunction detection between the EBS control unit and the trailer connection socket is not installed. When a trailer equipped …
1. Due to improper programming of the Crash Safety Module (ACSM6), malfunctions in the restraint system, pedestrian protection, or high-voltage battery unit shutdown function may result in the Check Control message or …
1. Due to improper programming of the Crash Safety Module (ACSM6), check control messages or airbag warning lights may not illuminate when malfunctions occur in the restraint system, pedestrian protection, or high-voltage …
Manufacturing defects in high-voltage battery cell modules may cause high-voltage battery malfunction. In rare cases, the high-voltage battery may discharge, potentially leading to fire in the worst scenario.
In the braking system, inadequate manufacturing quality of the brake master cylinder causes brake fluid to leak into the servo. This results in reduced brake pedal feel and, in worst cases, reduced …
The hand detection sensor mounted in the steering wheel may fail to detect when both hands are removed from the wheel due to improper manufacturing instructions for the steering wheel. As a …
In the electric brake booster, due to improper component specifications of the hydraulic pump motor, repeated frequent brake operations may cause internal wiring within the pump motor to break, resulting in insufficient …
In the power transmission system of wheel cranes, improper assembly during axle shaft manufacturing may result in the snap ring not being installed at the joint. Continued use in this condition may …
In the power transmission system of a wheel crane, improper assembly work during axle shaft manufacturing may result in the snap ring not being installed at the joint. Continued operation in this …
In excavator and loader brake piping, the machining dimensions of the section coupling to the differential housing are improper, resulting in some units with an excessively wide O-ring seating surface. This causes …
The electrical wiring routed beneath the engine of the forklift is protected by inadequate protective sheathing. During operation, dust and sand kicked up can enter the interior through gaps in the sheathing. …
In the advanced driver assistance system, the front wide-view camera activation processing program is improper, which may prevent the camera from activating during vehicle startup. As a result, the indicator light may …
The harness connector for the electric parking brake uses inappropriate resin material, which may cause the connector to crack due to effects from de-icing agents and similar substances. This may result in …
Inadequate strength analysis of the rear suspension toe link has resulted in insufficient rod strength in some units. In certain vehicles where the rear knuckle ball joint has been replaced with aftermarket …
The rear suspension toe link damper device has insufficient rod strength due to inadequate strength analysis. On some vehicles where the rear knuckle ball joint has been replaced with aftermarket parts, corrosion …
In the electrical system of rotary snow removal vehicles, improper wiring fastening methods can cause starter motor wiring and wiring clamps to abrade against each other due to vibration during continued use. …
In the electrical system of rotary snow removal vehicles, improper wiring fastening methods cause starter motor wiring and wire clamps to abrade due to running vibration, resulting in damage to the insulation. …
1. Safety components and interior/exterior trim parts installed for public road use may have insufficient evaluation of the components and mounting areas, resulting in malfunctioning lights, component detachment, or damage, potentially causing …
1. Safety components and interior/exterior trim parts installed for public road use have insufficient evaluation of the parts and mounting points. This may result in failure of lighting fixtures, detachment or damage …
1. Safety components and interior/exterior parts installed for public road use may have insufficient evaluation of the parts and mounting areas, resulting in loss of function due to lighting failure, component detachment, …
In large trucks and buses, the parking brake warning light switch is improperly designed, causing condensation water within the air piping to prevent normal switch operation. As a result, even when the …
In large tour buses, the electrical equipment control ECU program is defective, which may cause: ① The parking brake engagement status to display incorrectly even after the parking brake is released, and …
In large tour buses, the electrical control ECU program is inappropriate, which may cause: (1) the parking brake status to not display correctly even after releasing the parking brake, and brake lights, …
The passenger seat airbag inflator may allow moisture ingress when exposed to high temperature and high humidity environments for prolonged periods. This can result in abnormally elevated pressure within the inflator during …
The passenger seat airbag inflator may allow moisture ingress when exposed to high temperature and high humidity environments over extended periods. This can result in abnormal pressure rise within the inflator during …
In the rear axle level sensor that adjusts the optical axis according to load weight, improper assembly instructions during manufacturing have resulted in some units having the linkage connected in the reverse …
The 48V ground wiring beneath the front passenger seat may have been installed with improper fastening torque on the terminal fixing bolts during manufacturing. This can cause loss of electrical continuity due …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.