Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 31 of 175
Improper welding of the component securing the left and right rear wheel brakes to the rear axle shaft may cause the component to detach from the rear axle shaft during continued use. …
In wheel loaders, the vehicle control unit software that regulates brake light activation and deactivation was inadequate, potentially causing the brake light to remain illuminated continuously regardless of brake pedal operation. This …
The control program of the airbag control unit in the passenger seat occupancy detection system is inappropriate, which may cause the system to stop operating. As a result, even when a person …
On medium-sized buses, the fastening position of the floor panel fixing screw is inappropriate, which may cause the screw tip to interfere with the fuel piping. As a result, the fuel piping …
In medium-sized buses, the fastening position of the floor panel fixing screws is improper, which may cause the screw tip to interfere with the fuel piping. As a result, the fuel piping …
In the oil control valve that regulates the operation of the hydraulic VVT (variable valve timing mechanism) on the exhaust side of the R06A engine, internal rust can develop due to saltwater …
In certain shovel loaders, the power transmission device of the axle was produced without sufficient material evaluation, and some units do not meet design-intent performance. Continued operation in this condition may result …
In the driving support system, the collision mitigation brake control program is inappropriate, causing the system to react excessively to oncoming vehicles or roadside obstacles on curved roads. This may result in …
In vehicles equipped with a 6-speed DCT automatic transmission, the engine control computer's fuel injection control program is inappropriate, which may prevent proper control of injector fuel injection volume when the throttle …
The VDC (Vehicle Dynamics Control) unit has an inadequate electric parking brake control program. When vehicle vibration occurs while the electric parking brake is engaged, the sensor may react excessively and misidentify …
The capless fuel filler insert (fuel filler opening) in the fuel system has inadequate water-sealing design. Heavy rain and similar conditions may allow water ingress into the fuel system. This can lead …
In the low-pressure fuel pump impeller (resin-molded rotor) of gasoline engine vehicles, improper molding conditions result in reduced resin density, causing the impeller to swell and deform when exposed to fuel. This …
The spacers (left and right) of the rear seat grip handle are not secured to the vehicle body bracket with metal straps due to inadequate evaluation in airbag deployment testing. During curtain …
The parking brake design on agricultural chemical-spray vehicles is improper, causing inadequate engagement between the hook and gear, which may result in hook deformation. Continued use in this condition may cause the …
In the foot accelerator of agricultural tractors, improper installation orientation of the return spring causes the foot accelerator arm to tilt. This increases friction on the foot accelerator arm, resulting in poor …
In the tie rods of agricultural tractors, improper manufacturing of tie rod ends results in inadequate crimping of some tie rod ends. During steering operation, excessive stress is applied to the tie …
In the front suspension, improper manufacturing process control of the lateral link assembly between the link and subframe has resulted in installations that do not meet specifications. During use, fasteners between the …
Front and inter-axle propeller shafts have improper axial play adjustment during universal joint assembly, resulting in some units exceeding allowable axial play tolerances. Continued operation risks grease leakage, mud and water ingress …
The Emergency Stop Signal (ESS) flashing frequency is below the regulatory standard. In tractor units, if a bulb fails on the trailer's turn signal, the meter cluster turn signal flash rate does …
In the suction jet pump located inside the fuel tank, improper manufacturing work has resulted in some units with insufficient nozzle fixation. As a result, the nozzle may detach, reducing fuel supply …
In the electric power steering wiring, improper assembly procedures during manufacturing have resulted in damage to wire insulation in some units. Consequently, water ingress during use can cause electrical faults while driving, …
The hybrid battery trays in large tourist hybrid buses have insufficient corrosion resistance. During use, the trays corrode and develop holes. Water enters the interior of the trays and contacts the battery …
In large truck engines, if micro-voids exist at the maximum stress point during secondary resonance of the turbocharger turbine impeller, fatigue fracture initiated from these micro-voids may cause turbine impeller damage, resulting …
Due to improper programming of the ABS control unit, the warning light illuminates and ABS function fails to operate, which may result in increased braking distance.
In the brake system's hydraulic unit, inadequate manufacturing equipment control can cause the internal motor to sustain damage when high torque is required. This may result in activation of the brake warning …
In hybrid vehicles, the engine compartment harness routing is improper, resulting in insufficient clearance between the harness and the bracket securing the engine control unit. Consequently, the harness may interfere with the …
The wooden block storage support for crane operations, which is attached to the vehicle frame of a wheel crane, has an improper fastening method, which may cause loosening of the fixing bolts. …
In the high-voltage battery, foreign material may be present in the cell module due to improper manufacturing processes. This can cause a short circuit in the battery circuit, resulting in abnormal current …
On refrigerated/freezer vehicle air suspension remote control BOX mounting brackets, welding of components is not performed at the position specified in the drawings, which may cause cracks to develop in the bracket. …
In the gear change pedal, the shape of the change pedal arm is inadequate, resulting in insufficient weld strength between the change pedal boss and the arm. Repeated shifting operations can cause …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.