Before you buy, check it isn't under a dangerous recall.

In the integrated brake system hydraulic circuit control unit, improper manufacturing equipment settings result in inadequate welding between the hydraulic pump motor rotor and shaft in some units. Consequently, the rotor may …

In the electric brake booster, the mounting position of the magnet on the motor shaft of the rotational angle sensor, which is an internal component, is improper. This may cause the software …

The engine control computer has an inappropriate control program. When the throttle is opened during starting, ignition control does not function properly, and engine stall may occur during acceleration or re-acceleration after …

The engine control computer has an inappropriate control program. Carbon deposits accumulate in the combustion chamber, and portions may flake off and lodge in the seat surface of the exhaust or intake …

Due to inadequate work management, the retainer securing the brand emblem on the driver-side airbag cover may not be properly installed. Upon airbag deployment, the brand emblem or retainer may scatter, potentially …

Dashboard harness routing is improperly designed, allowing contact with the steering column. Vehicle vibration may damage the harness, potentially causing horn, windshield wipers, ADAS (advanced driver assistance systems), driver airbag, or turn …

In the brake booster, the fastening torque specification for the fixed nuts is inadequate, resulting in two locations not being properly torqued. Consequently, the fixed nuts may loosen during use, causing abnormal …

The cable harness for the brake fluid level sensor may contact the exhaust manifold heat shield due to inadequate assembly control during manufacturing. This can cause the insulation to be damaged by …

The driver-side airbag units shipped as replacement parts have improperly welded brackets for attachment to the steering wheel. During use, the weld points may crack and separate, potentially causing the airbag to …

The driver's side airbag may not fold properly due to inappropriate conditions in the airbag folding equipment. Consequently, when the airbag deploys, high-temperature gas from the inflator may tear the airbag, potentially …

In the crane vehicle's vehicle control unit (VCU), due to inappropriate programming, operating the PTO drive switch with the parking brake released may cause the vehicle to move unexpectedly.

The ISOFIX bracket on the right side of the right rear seat may be missing the handle for connecting a child seat due to improper manufacturing instructions. This prevents proper child seat …

In the electrical wiring of the starter motor, improper manufacturing instructions have resulted in wiring being installed in a manner that interferes with the starter motor housing. Consequently, vibration during operation can …

In the fuel system, the quick connector material of the fuel supply piping is inappropriate. Repeated exposure to excessive engine compartment temperatures can soften the connector, leading to premature degradation and cracking. …

The suction jet pump with fuel gauge mounted in the fuel tank may tilt during use due to improper assembly instructions at manufacturing. This can prevent accurate detection of remaining fuel, causing …

The bulb holder material in the rear combination lamp is inappropriate, causing the bulb holder to deform from bulb heat. This may result in poor contact, illuminating the warning light, and in …

The engine cooling system has an inadequate air-bleeding design. If the dedicated special tool is not used correctly when refilling coolant during repairs or other maintenance, air may not be properly bled …

In the fuel pump relay located in the engine room, improper material selection may cause substances generated by heat to adhere to the terminals. This can result in internal contact failure of …

Due to improper programming of the gateway module in the speedometer, the kilometer display may switch to mile display while driving. This may cause the driver to misidentify the displayed speed versus …

Due to inadequate work management, some vehicles have excessive fastening torque on the battery negative cable body-side ground attachment bolt. This can result in stripped threads on the bolt, causing loss of …

The design of the selective catalytic reduction (SCR) system and surrounding areas on the prime mover of the combine harvester does not adequately account for dust accumulation. Dust may accumulate in these …

The sound-damping foam pad installed on the underside of the fuel tank has insufficient moisture validation. When water ingress occurs, the pad can remain damp for extended periods. If moisture becomes corrosive, …

The ABS (anti-lock brake system) modulator has inadequate grease application equipment management, resulting in excessive grease being applied to the O-ring of the reservoir piston in some units. Consequently, grease migrates to …

The ESP (Electronic Stability Program) control unit has an improper control program that may cause deviations in yaw sensor calculations. As a result, ESP control may not be optimally executed according to …

The driver-side airbag inflator has inadequate moisture prevention, allowing the gas generant to absorb moisture. Consequently, if the gas generant undergoes repeated cycles of moisture absorption and drying during use, the airbag …

The quick connector material in the fuel supply piping of the fuel system is inappropriate. Repeated exposure to excessive engine compartment temperatures can soften the connector, causing premature deterioration and cracking. This …

The driver-side airbag inflator lacks adequate moisture protection, allowing the gas generant to absorb moisture. Repeated moisture absorption and drying cycles during use may prevent the airbag from deploying properly during activation.

Certain starter-alternators have gaps in the housing due to improper manufacturing tolerance settings. Moisture can enter the interior, and if circuits within the starter-alternator short-circuit, overheating may occur, potentially resulting in fire.

Certain inline 4-cylinder diesel engines have insufficient timing chain strength due to improper material selection and surface treatment. The timing chain may break during engine operation, potentially causing engine shutdown while driving …

Due to improper equipment settings during manufacturing, the hydraulic solenoid valve tip may be misaligned in the integrated brake system hydraulic circuit control unit. This can prevent proper hydraulic circuit establishment, potentially …