Before you buy, check it isn't under a dangerous recall.

The exhaust gas recirculation (EGR) module's cooler in diesel engines has insufficient durability, causing coolant leakage. Soot from exhaust gases mixes with coolant and accumulates inside the EGR module. When the accumulated …

The brake light switch has improper mounting instructions, resulting in some switches not being securely fixed. Repeated brake operation may cause the switch to detach from its bracket, resulting in the brake …

The steering wheel attachment to the steering column may have been improperly installed. Due to steering inputs during operation, the attachment nut can loosen and cause play at the joint. If use …

The suspension control unit may have improper programming, preventing correct recognition of rear axle height. Consequently, headlight beam axis adjustment may not be performed appropriately, and in the worst case, the beam …

On the power distribution module substrate, due to inadequate manufacturing equipment control, moisture-protective coating was applied over unwanted solder deposits. During use, cracks may develop in this coating. In high-humidity environments, this …

The impeller (resin fan wheel) in the low-pressure fuel pump may swell and deform due to improper molding conditions resulting in low resin density, which is susceptible to swelling from fuel. As …

The inflator of the front passenger airbag, when exposed to extremely high temperature and high humidity environments for extended periods, may allow moisture to enter the inflator. Consequently, upon airbag deployment, internal …

The passenger side airbag inflator may allow moisture ingress when exposed to high temperature and high humidity environments for extended periods. This can cause abnormal pressure rise in the inflator during airbag …

In the trailer braking system, the mounting instructions for the spring brake chamber pushrod (distance from mounting surface to joint pin center) are improper, resulting in some units being installed with excessive …

In the fuel tank, the rollover valve float may have gaps in its fitting portion due to improper dimensions of the float molding die. As a result, fuel can enter the float, …

In the torque converter of the continuously variable transmission (CVT), improper molding of the lockup clutch spring causes excessive stress during lockup mechanism operation, which may result in fracture. The fractured spring …

On the front right engine mount of the GH11 engine, improper fastening sequence of the bracket mounting bolts has created gaps between the bracket and suspension components. Engine vibration may cause the …

In the brake actuation air circuit of heavy-duty trucks, the desiccant regeneration air tank has insufficient durability evaluation, which may cause cracks in the tank and result in air leakage. This can …

In the steering apparatus of crane vehicle platforms, improper manufacturing instructions have resulted in insufficient wall thickness in the knuckle. This can cause cracking in the affected area during crane operations, and …

The driver-side airbag inflator has inadequate moisture protection, allowing the gas generant to absorb moisture. Repeated moisture absorption and drying during use may prevent normal deployment upon airbag actuation, risking occupant injury.

In large truck air dryers, the pressure test connector for compressed air has inappropriate material composition. Components contained in compressed air produced by the air compressor and high pressure can cause corrosion …

The fuel pump control program in the engine ECU is inappropriate, causing the fuel pump to draw air when fuel tank level is low. Air becomes compressed and heated during fuel supply …

On vehicles equipped with 2.0L turbocharged gasoline engines, the fuel hose material is unsuitable and may deteriorate prematurely due to heat and other factors. If use continues in this condition, fuel may …

The holder securing the front wheel brake hose has been improperly bent during manufacturing, resulting in incorrect installation in some units. Consequently, the holder may detach due to vibration during operation, and …

Improper routing of the horn electrical wiring causes contact with the front brake hose when the handlebar is turned left. This causes the brake hose protective sheath to wear; continued use in …

Due to improper work instructions, some anti-theft alarm harnesses lack dummy plugs on their connectors. Water can then seep along the harness into the Built-in System Interface (BSI) connector, causing internal short …

The driver-side airbag inflator has inadequate moisture protection, allowing the gas generant to absorb moisture. Repeated moisture absorption and drying cycles during use may prevent normal airbag deployment during actuation.

In full-tractor specification heavy-duty trucks, the identification label indicating rear brake system is not affixed to the 15L air tank for rear brakes due to improper instructions for label application.

Driver-side airbag inflators in large trucks and small buses have inadequate moisture protection, allowing the gas generant to absorb moisture. During use, repeated moisture absorption and drying cycles may prevent the airbag …

The driver-side airbag inflator has inadequate moisture protection, which may allow the gas generant to absorb moisture. If the gas generant undergoes repeated cycles of moisture absorption and drying during use, the …

The driver seat airbag inflator has inadequate moisture prevention, which may allow the propellant to absorb moisture. Consequently, if the propellant undergoes repeated cycles of moisture absorption and drying during vehicle use, …

The gas generant in the driver-side airbag inflator (gas generation device) may degrade due to moisture absorption. As a result, the airbag may not deploy normally during deployment, and in the worst …

In vehicles equipped with superchargers, the plastic spacer securing the fuel delivery pipe has inadequate material composition. Heat causes the spacer to deform, loosening the mounting bolt. Engine vibration may subsequently fracture …

In supercharged vehicles, the plastic spacer securing the fuel delivery pipe has inadequate material properties. Heat causes spacer deformation, leading to mounting bolt loosening. Engine vibration may fracture the bolt, resulting in …

Some low-pressure power steering hoses have insufficient length due to inadequate manufacturing process control. This causes increased routing angles, which can result in hose damage from vehicle vibration and other factors. In …