Before you buy, check it isn't under a dangerous recall.

The inflator (gas generator) of the replacement driver-side SRS airbag may experience degradation of the gas generant due to repeated cycles of environmental temperature and humidity changes. As a result, internal pressure …

On power distribution unit circuit boards, inadequate manufacturing equipment controls resulted in conformal coating applied over unwanted solder residue. During use, cracks may develop in the coating. In high-humidity environments, this can …

The electrical auxiliary heater element may have insufficient connector engagement during manufacturing, resulting in poor contact in some units. Continued operation in this condition may cause the affected component to overheat, with …

Due to improper settings of the machining equipment, some master cylinders in the braking system have shapes that deviate from specification. This may result in insufficient braking pressure, and in worst case …

In the rear axle housing of small trucks, improper welding procedures during the welding process have resulted in the flange at the housing end being welded in a tilted condition. This causes …

In small trucks, improper label application instructions for brake fluid type designation result in some vehicles lacking the required label. This violates Safety Standard Article 12 (Braking System Standard).

Brake calipers may develop corrosion on the piston bore metal surface due to inadequate surface treatment. The corroded piston bore creates resistance, restricting caliper piston movement and causing poor brake release. In …

In the electric parking brake, improper application of lubricating grease inside the electric parking brake actuator gears and inadequate design of the grease collection cavity volume can cause oil components from accumulated …

Due to inadequate manufacturing control in the driver-side airbag inflator, some inflator housings are not manufactured according to design specifications. Consequently, the inflator may rupture upon collision impact, and scattered metal fragments …

The blow-by gas heater in the engine's blow-by gas recirculation system has inadequate molding, causing cracks in the outer resin. When moisture infiltrates the cracks, they expand and short-circuit the electric heating …

The ignition switch included in the fairing kit has an improperly shaped sub-harness guide. When the handlebars are turned left or right, the sub-harness may be pulled excessively. This can cause wiring …

Due to improper programming in the airbag control module, reading airbag information from the event data recorder or similar devices may unintentionally overwrite the airbag control module's control program. This could result …

Certain air conditioning blower control units have inadequate water resistance due to improper housing design. Water ingress into the unit can cause internal electrical wiring short circuits and circuit board burnout, potentially …

Due to an inadequate control program in the airbag controller, the side airbag, curtain airbag, and seat belt pretensioner may malfunction when the rear door is closed forcefully. Consequently, in the worst …

In driver's side airbags, the cushion storage tool used in the manufacturing process is inappropriate, resulting in some units with damaged cushion covers. Consequently, some airbags have degraded cushioning function, and in …

The material composition of internal components in the rear brake light switch is inappropriate, allowing rainwater ingress to cause corrosion. Continued use may result in contact degradation or movable contact malfunction, causing …

In hybrid vehicle electrical wiring, improper work instructions during component assembly have resulted in electrical wiring interfering with the vehicle frame. Vibration during driving may cause the insulation to abrade, resulting in …

During the manufacturing process of the driver-side airbag inflator, humidity control of the gas generant was inadequate, resulting in some units being sealed with moisture-contaminated gas generant. Consequently, repeated large temperature fluctuations …

During panoramic sliding roof exterior trim replacement work, improper part catalog notation resulted in use of non-standard primer. This reduces adhesion between trim and frame, causing detachment. In worst case, the trim …

Due to an inappropriate control program in the combination meter, if an abnormality occurs in the brake system, the warning light may not operate, and the malfunction may not be detected.

In the front brake hoses, the crimped joint between the brake hose and pipe has an improper shape, which may cause the brake hose to bend excessively. Consequently, the brake hose may …

In rotary snow removal vehicles, improper adjustment of the brake valve results in some units having no brake free play. Consequently, if pedal displacement occurs depending on the operating environment, the brake …

In garbage trucks equipped with a water spray system, improper selection of the protective fuse may allow excessive current to flow when wiring shorts or other abnormalities occur, potentially causing the wire …

In the collision mitigation braking control system of large tractors, due to improper programming of the LPOS (Lane Position Object Sensor), forward-facing sensor and camera detection functionality may be degraded during straight-line …

Improper wiring assembly work in the electrical wiring has resulted in frame wire harnesses interfering with components around the frame on some vehicles. Due to vehicle vibration and other factors, the harness …

The ABS actuator has insufficient resistance to brake fluid of unstable properties or types other than those specified. This causes gel-like substances to form on the valve surface zinc plating, degrading valve …

In the engine cooling system, certain bleeder hoses have inadequate heat resistance due to improper material selection. This can cause cracking of the hose from thermal stress, resulting in coolant leakage and …

In the power transmission system, certain propeller shafts have insufficient durability due to improper shape and machining of the connection portion. This causes weakened fit at the connection, preventing the propeller shaft …

Certain front suspension components have insufficient durability due to inappropriate material selection and dimensional design of the swivel bearing. As a result, driving vibrations may cause cracks in the clamp portion that …

In the brake system, improper plating process control during brake caliper manufacturing may cause air bubbles to form between caliper components and brake fluid. These bubbles can accumulate within the brake system, …