Before you buy, check it isn't under a dangerous recall.

Driver-side or passenger-side airbag inflators with inadequate moisture protection of the gas generant may degrade when subjected to repeated temperature cycles in high-humidity environments. This can cause inflator container rupture during airbag …

The engine control unit's control program is inappropriate, which may prevent proper engine throttle control at low engine speeds. This can result in poor acceleration and, in the worst case, engine stall …

In the steering system, improper manufacturing of the left front wheel axle carrier may cause cracks to develop in the axle carrier due to impacts from rough road driving and similar conditions. …

The bolts securing the front suspension and lower arm lack sufficient strength, causing bolt fracture and abnormal noise in some vehicles. Continued operation in this condition risks lower arm detachment, resulting in …

The housing liner shape on the front fender is improper, causing the front tire to contact the housing liner when the steering is turned to maximum angle. This does not comply with …

In second-row rear seats, improper assembly instructions for the seat frame result in some reclining mechanisms not being correctly assembled. Consequently, the seat backrest is not fixed in place and may collapse …

The seat belt retractor on the front passenger seat may have been manufactured improperly, causing the seat belt to fail to lock during hard braking and similar situations. As a result, the …

In the front brake, certain units have insufficient piston strength within the master cylinder due to improper design. During brake actuation, brake fluid pressure may cause cracks to develop in the piston. …

In the front brake, the master cylinder design is inadequate, resulting in insufficient piston strength within the cylinder. During brake operation, brake fluid pressure may cause cracks in the piston. If operation …

In the electrical system, some alternators have inadequate design, resulting in insufficient electrical capacity of the rectifier. As a result, the rectifier generates excessive heat. If the vehicle continues to be used …

In hybrid vehicles equipped with mechanical automatic transmissions, an improper control program in the controller may cause the transmission to engage a gear different from the intended gear during operation. This activates …

In the combination meter, due to an inappropriate communication program, communication signals cannot be transmitted or received, causing system abnormalities such as Advanced Smart City Brake Support to be displayed on the …

In the engines of excavators and loaders, the band securing the hose between the aftercooler and engine is improperly assembled, causing the band tightening bolt to contact the fuel hose between the …

The bulkhead insulation has improper dimensions, causing the insulation to overlap and adhere to the lower edge of the windshield. This results in poor windshield adhesion. When the passenger airbag deploys, the …

The door lock component (excluding driver-side door) on the left-side door has been manufactured improperly. As a result, the door may open when the outer handle is pulled even when the door …

The engine control unit's control program is defective, which may cause engine stall immediately before vehicle stop during braking deceleration or immediately after restart from eco-stop function. This may prevent the driver …

The fuel filter vibration resistance assessment in the fuel system is inadequate, causing the fuel hose connection to wear due to engine vibration and other factors. Continued use in this condition allows …

Certain driver-side airbag inflators have improper manufacturing controls, resulting in some units where the igniter composition does not meet design specifications. Consequently, the driver-side airbag may fail to deploy in a collision, …

In air conditioning units, improper manufacturing of the auxiliary heater can cause corrosion of the terminal portions at the wiring connection points (connectors). Continued use in this condition increases electrical resistance, causing …

In the braking system, the durability evaluation of the ABS/ESC control unit is insufficient. Engine heat and other factors may cause cracks to develop in IC chips (power control units) mounted on …

In the braking system, the ABS/ESC control unit durability assessment was insufficient. Engine heat and other factors may cause cracks to develop in the IC chip (power control unit) mounted on the …

In agricultural tractor hydrostatic continuously variable transmissions (HST), the emergency brake hydraulic line routing is inappropriate. Engine vibration and other factors cause the line to oscillate, subjecting it to excessive stress and …

In the drag link of medium-duty trucks, welding work at the ball joint connection may be performed improperly, resulting in welding positions that deviate from specifications. Continued use in this condition may …

In large trucks, the pre-plating acid pickling process for the fixing clamp fastening bolt of the front axle right-side tie rod end was inadequate, causing hydrogen embrittlement that has reduced bolt strength …

In large trucks, improper assembly of the front-wheel brake chamber in the braking system has resulted in insufficient tightening torque on plugs (sealing caps) or test nipples and brake hose connections (nipples …

In large trucks equipped with air suspension height-adjustment devices, the shock absorber piston structure is inadequate. Lateral forces cause excessive contact pressure between the piston and cylinder. When the vehicle is repeatedly …

The airbag control unit has insufficient electrical noise immunity. When battery wiring is severed during a collision, the resulting electrical noise from the disconnection can damage the electronic circuit board within the …

In the airbag control unit, improper manufacturing of the unit's circuit board can cause corrosion of the IC chip that controls airbag ignition devices. Continued use in this condition may allow corrosion …

In medium-duty truck pneumatic brakes, improper tightening work on the relay valve mounting bracket has resulted in some units missing fastening bolts. If operation continues in this condition, running vibration may cause …

In medium-duty truck air-hydraulic hybrid brakes, the piston cup groove machining in the rear wheel cylinder may be inadequate. If operation continues in this condition, the seal performance between the piston cup …