Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 68 of 173
The waterproof filter affixed to the ventilation port of the electric power steering control unit may have been manufactured improperly, resulting in units without adequate waterproofing. If rainwater enters through the ventilation …
Driver or passenger airbag inflators may have inadequate moisture protection of the gas generant. When exposed to repeated large temperature fluctuations in high-humidity environments, the gas generant may degrade. Consequently, the inflator …
The driver-side airbag inflator lacks adequate moisture protection for its gas generant. Under high-humidity environments with repeated large temperature fluctuations, the gas generant can degrade. This may cause the inflator container to …
In the steering system, improper manufacturing of the coupling component (steering yoke) that connects the steering wheel and steering gearbox has resulted in play developing at the connection between the coupling component …
The inflator (inflation device) for the passenger-side airbag has inadequate moisture prevention for its gas generant, causing the gas generant to degrade through repeated temperature and humidity cycles. This may result in …
In the power transmission system, the oil seal of the clutch push lever may have fine cracks due to improper manufacturing. Continued use could cause the cracks to propagate under engine oil …
In the power transmission system, the spider pin geometry within the differential is inadequate, causing the oil film on the spider pin to rupture during high-load operation. This results in spider pin …
The brake piston seal in the braking system has inadequate heat resistance due to improper selection. Heat from braking causes the seal to deteriorate, resulting in brake fluid leakage and warning light …
In large tractors, improper tightening of the front brake hose connection may result in insufficient clamp force at the hose joint. This can cause the connection to loosen, leading to air leakage …
Due to improper programming in the airbag control module, the self-diagnostic function may activate and remain activated when subjected to vibration, such as when curbing. As a result, the signal to deploy …
In hydraulic clutch master cylinders, inadequate internal cleaning during manufacturing leaves residual manufacturing chemicals that are not removed. These chemicals react with brake fluid inside the master cylinder, causing gas bubble formation …
In the engine, improper routing design of the ignition coil electrical wiring can cause the wiring to become pinched between the holder and the main harness clamp. Additionally, improper manufacturing of the …
On the under-mirror used for vehicle loading operations in car transporters, the mirror bracket shape is inadequate, which can cause cracks to develop in the welded section due to vibration during operation. …
The parking brake cable attachment method is improper, causing the cable to detach from the operating lever due to vehicle vibration, which may result in parking brake failure.
The transmission shift lever returns to center position after selecting a shift position. If the driver attempts to shift to Park before the vehicle comes to a complete stop, the shift may …
The transmission shift lever returns to the center position after selecting a shift position. If the driver attempts to shift to Park before the vehicle comes to a complete stop, the shift …
In the secondary air pump of the exhaust emission control system, improper contact pressure within the relay controlling the pump causes arc discharge when contacts close, leading to contact welding and continuous …
In large truck engines, the closed ventilator (blow-by gas recirculation device) has an improper structure, causing the ventilator element to become clogged before the scheduled replacement interval. This results in increased crankcase …
Certain large and medium-duty trucks have inter-axle differentials with improperly manufactured input shaft flanges, resulting in unbalanced input shaft rotation. This imbalance causes bearing damage, and if operation continues, bearings will seize, …
In the engine control unit of medium and small trucks, improper coating of the ventilation vent plug mounting section causes corrosion due to water exposure, reducing waterproofing. Water may then infiltrate the …
The driver-side airbag inflator may have inadequate moisture protection of the gas generant. Repeated large temperature fluctuations in high-humidity environments can degrade the gas generant, potentially causing the inflator housing to rupture …
In the windshield wiper system, due to improper manufacturing of the bottom cover (with built-in electrical circuit) of the front wiper motor, the electrical contact relay joint and worm wheel may interfere …
In idle-stop-equipped vehicles, the starter-integrated alternator has insufficient electrical circuit resistance. High current during restart from idle-stop can damage internal components, causing circuit shorts that prevent restart from idle-stop. In the worst …
In the automatic transmission, the connector and cable for engaging the parking lock are improperly installed. When the shift is operated to P range, the connection between the connector and cable may …
Passenger-side airbag inflators may have improperly welded high-pressure gas sealing valves, resulting in reduced valve opening pressure. This may cause unintended high-pressure gas release and airbag deployment.
Driver-side or passenger-side airbag inflators may have inadequate moisture protection of the gas generant. Repeated large temperature variations in high-humidity environments can cause degradation of the gas generant, potentially resulting in inflator …
The inflators in the driver's and/or front passenger airbags may have inadequate moisture protection for the gas generant. Repeated large temperature fluctuations in high-humidity environments can cause the gas generant to degrade, …
The rear axle shaft in agricultural tractors may develop cracks under high load conditions during field work due to improper heat treatment of the shaft. If use continues in this condition, cracks …
The resin inlet cover inside the fuel pump is made of inappropriate material. When exposed to test oil used during manufacturing for extended periods, the inlet cover may swell during use and …
The plastic inlet cover material inside the fuel pump is unsuitable. When exposed to test oil used during manufacturing for extended periods, the inlet cover may swell during use and interfere with …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.