Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 85 of 173
The headlight electrical wiring routing is improper, causing the wiring to flex when the handlebars are moved left and right. Continued use in this condition may result in the wiring breaking due …
The tensioner that applies tension to the engine timing chain may wear prematurely due to improper manufacturing. This can cause abnormal noise from the timing chain, and if operation continues in this …
The driver-side SRS airbag inflator contains a defective partition plate that forms the airbag inflation gas flow path. During airbag deployment, this causes abnormal pressure buildup inside the inflator, potentially rupturing and …
The brake vacuum electric pump, which supplies negative pressure to the brake booster, has an improperly positioned exhaust port. Mud and sand containing de-icing agent adhere to and enter the exhaust port, …
The control program of the EV ECU that controls the brake vacuum electric pump supplying negative pressure to the brake booster is inappropriate, which may cause erroneous detection of relay contact stiction. …
The control relay for the brake vacuum electric pump, which supplies negative pressure to the brake booster, may have inadequate crimp management, causing the relay contacts to stick in the on position. …
The heat treatment of the brake caliper mounting bolts is inadequate, resulting in insufficient bolt strength. Continued use in this condition may cause bolt fracture and reduced braking force.
Certain passenger-side airbag components have been manufactured improperly. During deployment in a collision, these components may separate from the airbag housing, and in the worst case, the detached component could strike occupants.
In the hydraulic circuit of the steering system, when the hydraulic fluid filter contamination exceeds acceptable limits and the warning light is illuminated, and an overdue low-pressure hose past its service interval …
The parking brake disc mounted on the front axle input shaft has an inadequate structure, allowing soil and debris to enter the spline. This causes axial sliding of the spline, leading to …
The bolts fastening the front suspension to the vehicle frame lack sufficient clamping force, causing them to loosen and generate abnormal noise. Continued use may result in bolt detachment, potentially degrading steering …
The transmission control switch internal circuit board design is inadequate, which may cause internal short circuits due to vehicle vibration and similar factors. If this occurs, the transmission shifts to neutral, resulting …
The fuel tank mounted at the rear of the vehicle may rupture and cause fuel leakage when subjected to rear-end collision under specific conditions. In the worst case, this could lead to …
The fuel tank mounted to the vehicle's rear may rupture and cause fuel leakage when struck from behind under specific circumstances. In the worst case, this could result in vehicle fire. Although …
In the steering system of combine harvesters, certain units have improperly adjusted microswitches that detect steering lever position. This may prevent steering operation even when the steering lever is manipulated.
In the steering system of combine harvesters, certain units have improperly adjusted microswitches that detect steering lever position. As a result, steering operation may become impossible despite lever actuation.
In the braking system of wheel cranes, the brake hose routing is improper, and the handle linkage mechanism may contact the brake hose during steering operations. Continued use in this condition may …
Improper welding of the hook that secures the spare tire carrier can cause the weld to separate and the hook to detach. This may cause the spare tire carrier to tilt, and …
In the steering apparatus of wheel cranes, improper tightening torque of the tie-rod end clamp bolt causes loss of clamping force. This results in looseness in the tie-rod end threaded section, and …
The wiring harness for the ignition switch is improperly secured, causing interference with the steering shaft in some vehicles. Continued use may result in the harness insulation being damaged through friction with …
The fuel pump's internal rotating components have improper coating that may peel and jam in the rotating section, increasing rotational resistance and reducing fuel discharge volume. In worst cases, this may cause …
In heavy-duty trucks equipped with 12-speed mechanical automatic transmissions, oil mist contained in compressed air supplied from the air compressor undergoes oxidative degradation, generating black sticky deposits. These deposits can cause seizure …
In the electronically controlled rear suspension, improper manufacturing of the damper spring causes the spring to not compress vertically when excessive force is applied to the suspension, risking suspension damage. This results …
The wheel cylinders for the rear wheel primary brake have insufficient corrosion resistance on the piston. During use, moisture from the atmosphere can enter the cylinder, causing rust to form on the …
Some front brake hoses are installed pinched between the fuel tank and frame. Continued use in this condition may cause front brake drag during operation, and in the worst case, the front …
In the front suspension, some lower arm mounting bolts have insufficient strength. If vehicles continue to be used in this condition, the bolts may fracture, causing abnormal noise and potentially affecting steering …
The fuel pump quick coupler removal/installation instructions are inadequate, which can cause cracks to develop in the fuel pump mount dome. As thermal expansion and contraction of the fuel pump progresses the …
Due to improper ECU programming, when the ECU-estimated clutch friction characteristics deviate from actual clutch friction characteristics during EV mode driving and the engine is started by motor drive, excessive motor driving …
The swing-lock mechanism that maintains the vehicle's upright position when the parking brake is engaged has improper machining of the support bracket, which can result in shallow engagement between the swing-lock pole …
In the fuel piping of wheel loaders, due to inappropriate piping configuration and material, fuel piping cracks may develop under the pulsating load of the fuel pump. If operation continues in this …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.