Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 86 of 175
In rotary snow removal vehicles equipped with heated windshield glass, the electrical connector for the heated glass wiring has insufficient electrical capacity, which may cause electrical contacts to generate heat. Continued use …
In the fuel pump of light-duty trucks, cracks may develop in the resin component due to ultraviolet degradation during use and residual stress from manufacturing. Continued operation in this condition could allow …
During assembly of the brake light switch, work gloves contaminated with insulating lubricant oil caused trace amounts of lubricant to enter the switch contact surfaces, resulting in the formation of insulating deposits. …
Due to improper assembly procedures in the switch sleeve component of the brake booster's brake assist mechanism, cracks may develop in the affected part. When the brake assist mechanism activates, the switch …
The accessory drive belt material is inappropriate, causing the resin pulley to wear in a slanted manner in some cases. Continued use may result in belt damage and detachment, illumination of the …
The passenger-seat airbag inflator may allow moisture ingress when exposed to high-temperature, high-humidity environments for prolonged periods. This can cause abnormal pressure rise in the inflator during airbag deployment, resulting in inflator …
The passenger seat airbag inflator, when exposed to prolonged high-temperature and high-humidity environments, may allow moisture ingress. This can cause abnormal pressure buildup within the inflator upon airbag deployment, resulting in inflator …
During the manufacturing process of the rear wheel brake upper spring, the fixture geometry was inappropriate, causing scratches on some springs. Continued use of affected springs may result in fracture of the …
In starter motors of vehicles without idle stop function, insufficient interference fit between the motor coil and shaft may cause the motor coil to shift during starting input. Continued use can result …
The headlight electrical wiring routing is improper, causing the wiring to flex when the handlebars are moved left and right. Continued use in this condition may result in the wiring breaking due …
The tensioner that applies tension to the engine timing chain may wear prematurely due to improper manufacturing. This can cause abnormal noise from the timing chain, and if operation continues in this …
The driver-side SRS airbag inflator contains a defective partition plate that forms the airbag inflation gas flow path. During airbag deployment, this causes abnormal pressure buildup inside the inflator, potentially rupturing and …
The brake vacuum electric pump, which supplies negative pressure to the brake booster, has an improperly positioned exhaust port. Mud and sand containing de-icing agent adhere to and enter the exhaust port, …
The control program of the EV ECU that controls the brake vacuum electric pump supplying negative pressure to the brake booster is inappropriate, which may cause erroneous detection of relay contact stiction. …
The control relay for the brake vacuum electric pump, which supplies negative pressure to the brake booster, may have inadequate crimp management, causing the relay contacts to stick in the on position. …
The heat treatment of the brake caliper mounting bolts is inadequate, resulting in insufficient bolt strength. Continued use in this condition may cause bolt fracture and reduced braking force.
Certain passenger-side airbag components have been manufactured improperly. During deployment in a collision, these components may separate from the airbag housing, and in the worst case, the detached component could strike occupants.
In the hydraulic circuit of the steering system, when the hydraulic fluid filter contamination exceeds acceptable limits and the warning light is illuminated, and an overdue low-pressure hose past its service interval …
The parking brake disc mounted on the front axle input shaft has an inadequate structure, allowing soil and debris to enter the spline. This causes axial sliding of the spline, leading to …
The bolts fastening the front suspension to the vehicle frame lack sufficient clamping force, causing them to loosen and generate abnormal noise. Continued use may result in bolt detachment, potentially degrading steering …
The transmission control switch internal circuit board design is inadequate, which may cause internal short circuits due to vehicle vibration and similar factors. If this occurs, the transmission shifts to neutral, resulting …
The fuel tank mounted at the rear of the vehicle may rupture and cause fuel leakage when subjected to rear-end collision under specific conditions. In the worst case, this could lead to …
The fuel tank mounted to the vehicle's rear may rupture and cause fuel leakage when struck from behind under specific circumstances. In the worst case, this could result in vehicle fire. Although …
In the steering system of combine harvesters, certain units have improperly adjusted microswitches that detect steering lever position. This may prevent steering operation even when the steering lever is manipulated.
In the steering system of combine harvesters, certain units have improperly adjusted microswitches that detect steering lever position. As a result, steering operation may become impossible despite lever actuation.
In the braking system of wheel cranes, the brake hose routing is improper, and the handle linkage mechanism may contact the brake hose during steering operations. Continued use in this condition may …
Improper welding of the hook that secures the spare tire carrier can cause the weld to separate and the hook to detach. This may cause the spare tire carrier to tilt, and …
In the steering apparatus of wheel cranes, improper tightening torque of the tie-rod end clamp bolt causes loss of clamping force. This results in looseness in the tie-rod end threaded section, and …
The wiring harness for the ignition switch is improperly secured, causing interference with the steering shaft in some vehicles. Continued use may result in the harness insulation being damaged through friction with …
The fuel pump's internal rotating components have improper coating that may peel and jam in the rotating section, increasing rotational resistance and reducing fuel discharge volume. In worst cases, this may cause …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.