The ball joint attachment points connecting the knuckle arm to the steering cylinder or tie rod lack sufficient strength. Repeated excessive loads from work impacts cause the fastening nuts or bolts to …
小松 GD305A-1 1986–2005
小松 GD305A-3 1986–2005
小松 GD355A-1 1986–2005
小松 GD355A-3 1986–2005
小松 GD405A-2 1986–2005
+1 more
In the primary braking system, insufficient bonding strength between the brake shoe and lining may cause cracking in the lining. If operation continues in this condition, the lining may separate, potentially resulting …
小松 GD305A-3 1997–2002
小松 GD355A-3 1997–2002
小松 GD405A-3 1997–2002
The chain in the secondary reduction gear (tandem drive unit) of the power transmission system has insufficient strength. Continuous operation of the primary brake causes brake lining temperature to rise and braking …
小松 GD305A-3 1997–2002
小松 GD355A-3 1997–2002
Due to machining defects in the drive shaft, some units have been machined to a reduced outer diameter and are not securely fixed to the transmission-side bearing. As a result, when driving …
BMW MINI Cooper S 2005
BMW MINI Cooper S Convertible 2005
The ratchet mechanism of the parking brake contains improperly machined detent teeth that may slip, preventing the lever from being locked. Repeated use of the parking brake may result in complete loss …
Hyundai JM 2005
Improper routing of electrical wiring in the engine compartment causes interference with the transmission mount on certain vehicles. Continued operation may result in wiring damage due to engine vibration, leading to short …
BMW MINI Cooper S 2004–2005
BMW MINI Cooper S Convertible 2004–2005
The hydraulic sensor mounted on the side of the engine is installed improperly. Engine vibration causes excessive stress on the threaded portion of the fitting used to attach the pressure sensor, resulting …
カトウ KR512 2002–2004
カトウ SD-KR512 2002–2004
The belt tensioner, which maintains proper tension on the accessory drive belt, has insufficient strength in the crimped section of the pulley mounting bracket that secures the pulley. Due to reaction force …
Isuzu Forward 2004–2005
The fuel line routing from the fuel tank to the engine is improper, causing the fuel line to interfere with the air conditioning duct in some vehicles. Continued use in this condition …
Isuzu Gala 1996–1999
The automatic transmission oil strainer has insufficient capacity, causing it to clog with clutch wear particles and resulting in inadequate hydraulic pressure. Continued operation in this condition may lead to loss of …
Mazda AZ Offroad 1998–2004
Mazda Scrum 1998–2004
Suzuki Every 1998–2004
Suzuki Jimny 1998–2004
The EGR (exhaust gas recirculation) pipe lacks sufficient structural strength. Thermal expansion and contraction of the pipe due to exhaust heat and engine vibration may cause cracks to develop. Continued use in …
Mitsubishi KL-MS86MM 2000–2005
Mitsubishi KL-MS86MN 2000–2005
Mitsubishi KL-MS86MP 2000–2005
Mitsubishi KL-MS86MS 2000–2005
Mitsubishi MU612TX 2000–2005
Some sensors within the airbag control unit have improper processing, which can cause electrical circuit short circuits. As a result, the airbag may suddenly deploy when the ignition switch is operated.
キャデラック CTS 2003–2004
キャデラック SRX 2003–2004
The check valve installed between the brake booster and intake manifold is made of inappropriate material. Under high ambient temperatures with repeated high-load operation, engine temperature rises and the check valve may …
サーブ 9-3 2003–2005
During assembly of the parking brake lever, a washer was omitted inside the lever in some units, resulting in insufficient locking force on the block that secures the lever. Consequently, the parking …
Mercedes-Benz ACTROS 2003–2005
The front wheel hub lacks sufficient strength and torsional rigidity. Repeated heavy braking during operation causes hub deformation with stress concentration at the spoke area, potentially resulting in spoke fracture. Continued use …
KTM 400 LC4 1998–2003
KTM 640 Adventure 1998–2003
KTM 640 LC4 1998–2003
Some transmission input shafts in the power transmission unit have inadequate strength due to improper heat treatment. Continued use may result in fracture of the input shaft in the worst case, rendering …
タダノ CREVO350 2004
The attachment bolts securing the hydraulic power steering gearbox to the subframe are insufficiently torqued. Repeated stationary steering operations can cause these bolts to loosen. Continued use may result in bolt fracture, …
Honda Step WGN 2005
The fuel tank breather hose quick-joint connector may have insufficient engagement, causing the seal (O-ring) to not make proper contact with the joint pipe. This compromises the seal integrity at the quick-joint …
Honda Step WGN 2005
During assembly, improper brake fluid injection causes excessive force at the brake reservoir tank and brake master cylinder junction, causing the rubber seal at this junction to fold and leak fluid. Continued …
Daihatsu Mira 2005
②In the front suspension system, lower arms manufactured through an improper forging process were installed, and some of these lower arms developed cracks in the ball joint socket area. As a result, …
Mazda RX-8 2003–2005
The engine control computer program is inappropriate, causing the engine to remain at high RPM and continue running even after the vehicle is stopped. High temperatures develop beneath the vehicle floor, potentially …
Mazda RX-8 2003–2005
Battery water-proofing measures are insufficient, allowing rainwater to contact the battery top surface. When the battery is replaced with a unit other than the factory-installed battery, rainwater may enter the battery interior …
Mazda Premacy 1999–2004
ニホンフォード Isuzu Axiom 1999–2004
The snap ring, which is designed to prevent disengagement of the left front drive shaft from the differential side gear within the transmission, has an inappropriate shape that results in insufficient engagement …
Chevrolet Cruze 2001–2004
Suzuki Swift 2001–2004
The front differential mounting angle is improper on some vehicles, causing accelerated wear at the connection between the front differential and front propeller shaft. Continued operation in this condition allows wear to …
Land Rover Range Rover 2002–2003
In heavy-duty trucks equipped with automatic transmissions, the flywheel that transmits engine torque to the torque converter has an inappropriate shape. When operating at high engine speeds, excessive stress develops at the …
Mitsubishi KC-FR529JX 1994–2000
Mitsubishi KC-FS419TZ 1994–2000
Mitsubishi KC-FS519VZ 1994–2000
Mitsubishi KC-FU419N 1994–2000
Mitsubishi KC-FU519NY 1994–2000
+7 more
On medium-sized all-wheel-drive vehicles, the front brake pipe fixing method is inadequate, causing the brake pipe to resonate and crack due to brake drum vibration during braking. Continued use in this condition …
Mitsubishi KK-FL63HD 1999–2003
Mitsubishi KK-FL63HE 1999–2003
Mitsubishi KK-FL63HEX 1999–2003
Mitsubishi KK-FL63HG 1999–2003
Mitsubishi KK-FL63HGX 1999–2003
+6 more
The press-forming of the clamp that secures the front stabilizer bar to the vehicle body is inadequate, resulting in insufficient durability of the clamp in some units. Due to vibration during driving, …
Renault Scenic 2001
Injuries — Risk of injury: Possible dislodgement of the rubber sealing boots protecting the steering tie rod, that can result in rapid wear and possible tie rod end separation with loss of …
The belt-type continuously variable transmission (CVT) contains metal belt segments (elements) with improper separation after press processing, resulting in deformed element bodies. This causes concentrated stress at the element root under driving …
Honda Fit Aria 2003
The metal belt-type continuously variable transmission (CVT) contains elements (links) whose separation following press machining is improper, resulting in deformation of some element bodies. This causes concentrated stress at the element root …
Honda Civic Hybrid 2003
Honda Fit 2003
Honda Mobilio 2003
Honda Mobilio Spike 2003