The universal joint section on the transmission side of the propeller shaft has a large angle, causing the temperature of this section to rise during high-speed driving. This accelerates the degradation of …
Toyota Toyota Town Ace 1993–1999
Toyota Toyota Town Ace 4WD 1993–1999
Toyota Toyota Lite Ace 1993–1999
Toyota Toyota Lite Ace 4WD 1993–1999
The hood locking mechanism securing the hood to the vehicle body contains insufficiently welded strikers attached to the hood. Continued use in this condition may cause the striker weld to separate. If …
Mazda Anfini RX-7 1996
Poor machining precision of the tilt bracket boss that connects the tailgate lift link causes stress concentration at the welded connection, which may result in cracking. If the vehicle continues to be …
Isuzu Isuzu GIGA 2001–2004
The exhaust pipe bellows section is secured using an improper method, which may cause cracks to develop in the bellows due to engine vibration. Continued use in this condition may result in …
Nissan - 2003–2005
In vehicle-mounted simple cranes, the push-pull cable detecting the limit switch position—a safety device for reliably determining crane operation and traveling states—has improper crimping positioning. Consequently, some units fail to detect the …
Mitsubishi KK-FE62EE 2005
Mitsubishi KK-FE63EE 2005
Mitsubishi KK-FE71CBD 2005
Mitsubishi KK-FE73EC 2005
Mitsubishi KK-FE82CE 2005
+27 more
Fire — Risk of fire. The second heating system is inadvertently activated during a garage/dealer intervention on the heating system, the structure of the second heating system can overheat; burning smell and …
The welded joint between the propeller shaft pipe and spline shaft in the power transmission system has insufficient fatigue strength. Repeated excessive hard acceleration or hill starts can cause cracks to develop …
Mitsubishi P-FP415DR 1983–1991
Mitsubishi P-FP418DR 1983–1991
Mitsubishi P-FP419DR 1983–1991
Mitsubishi P-FP445DR 1983–1991
Mitsubishi P-FP449DR 1983–1991
+26 more
The casting process of the transfer case, which is a recall remedy component, was conducted improperly, resulting in core sand remaining in the oil holes within the transfer case. Some oil holes …
Mitsubishi P-MJ117F 1985–1995
Mitsubishi P-MJ527F 1985–1995
Mitsubishi P-MK126F 1985–1995
Mitsubishi U-MJ117F 1985–1995
Mitsubishi U-MJ217F 1985–1995
+3 more
In vehicles where the fuel tank orientation was changed from horizontal to vertical mounting, the attachment bolts securing the fuel tank to the vehicle body via brackets (tank support, tank support bracket) …
Mitsubishi KC-MM719J 1996–2000
Mitsubishi KC-MP317K 1996–2000
Mitsubishi KC-MP337K 1996–2000
Mitsubishi KC-MP337M 1996–2000
Mitsubishi KC-MP717K 1996–2000
+2 more
Some rear door exterior handle door-open levers have defective riveting at the pivot point. This causes the lever to not fully return when the door is closed, preventing the latch from securing …
Subaru Legacy 2003–2004
The electrical control forward/reverse control unit has an inadequate waterproof structure at the wiring outlet, allowing water to enter the unit interior during washing and other operations, causing corrosion of the variable …
サカイ ER550F 2002–2005
サカイ ER551F 2002–2005
The fastening torque specification for the front axle mounting bolts is inappropriate. Repeated loads during snow removal operations may cause bolt loosening. Additionally, on some vehicles, paint residue remained on the front …
コべルコ LK40Z 1992–2005
コべルコ LK50Z 1992–2005
神鋼 LK40Z 1992–2005
神鋼 LK50Z 1992–2005
The impeller material in the fuel pump is unsuitable, causing the impeller to swell and deform due to fuel components, potentially interfering with the impeller case. Continued operation may result in impeller …
Suzuki Escudo 2004–2005
Suzuki Swift 2004–2005
Improper solder joints on internal terminals of the injection relay controlling fuel supply and the main relay controlling power supply may cause relay malfunction. Continued use in this condition could result in …
ドカテイ Monster 400 2004
Insufficient fastening torque on bolts securing the tailgate stopper to the body-side bracket allows bolts to loosen during use. Continued operation causes play at the bolt location, increasing stress. In worst cases, …
Mitsubishi Libero 1992–2002
Due to improper electrical circuitry in the lighting system, the brake light does not illuminate when the auxiliary braking device (electromagnetic retarder) is activated. Additionally, this defect can damage the brake light …
Nissan Condor 2004–2005
The fastening bolts securing the transmission shift and select rod mounting brackets were improperly tightened, resulting in some bolts becoming loose. Continued operation in this condition may cause the bolts to detach, …
Mitsubishi PA-BE63DE 2005
Mitsubishi PA-BE63DG 2005
Mitsubishi PA-BE64DG 2005
Insufficient strength in the knuckle stopper area of the front axle can result in excessive stress on the kingpin boss during vehicle cornering and similar operations, potentially causing cracks in the stopper …
Mitsubishi KC-MJ218F 1993–2004
Mitsubishi KC-MJ219L 1993–2004
Mitsubishi KC-MJ629F 1993–2004
Mitsubishi KC-MK219F 1993–2004
Mitsubishi KC-MK219J 1993–2004
+19 more
Improper machining of the key groove in the clutch release fork creates a stress concentration structure with insufficient strength in some units. Repeated clutch operation causes cracks to develop in the fork. …
Mitsubishi KC-FP510DKR 1994–2005
Mitsubishi KC-FP510DR 1994–2005
Mitsubishi KC-FP510GR 1994–2005
Mitsubishi KC-FP511DKR 1994–2005
Mitsubishi KC-FP511DR 1994–2005
+27 more
The cooling water hose of the fluid-type auxiliary braking device mounted on the transmission has insufficient durability. Cracks develop due to vibration during operation, and in some cases the hose becomes detached. …
Mitsubishi KC-FV513HR 1996–2005
Mitsubishi KC-FV514HR 1996–2005
Mitsubishi KC-FV515HR 1996–2005
Mitsubishi KL-FP50JDR 1996–2005
Mitsubishi KL-FP50JGR 1996–2005
+27 more
The lower radius rod on the front axle has insufficient strength for extended use beyond design specifications, and may develop cracks. Continued operation in this condition could result in rod fracture in …
Mitsubishi P-MS713N 1984–1988
Mitsubishi P-MS713S 1984–1988
Mitsubishi P-MS715N 1984–1988
Mitsubishi P-MS715NA 1984–1988
Mitsubishi P-MS715S 1984–1988
+7 more
The lower radius rod on the rear axle has insufficient strength. Repeated cyclic loading during low-speed turning on mountain roads and similar conditions may cause cracking in the rod. Continued use in …
Mitsubishi P-MS713N 1984–1988
Mitsubishi P-MS713S 1984–1988
Mitsubishi P-MS715N 1984–1988
Mitsubishi P-MS715NA 1984–1988
Mitsubishi P-MS715S 1984–1988
+7 more
The air charge pipe, which supplies compressed air to the brake system air tank, has insufficient strength. Cracks may develop in this pipe due to vehicle body vibration and similar factors. If …
Mitsubishi KC-MS822P 1995–2005
Mitsubishi KC-MS822PA 1995–2005
Mitsubishi KC-MU612T 1995–2005
Mitsubishi KL-MS85KN 1995–2005
Mitsubishi KL-MS86MM 1995–2005
+3 more
Some airbag control units were mistakenly equipped with a passenger vehicle G-sensor (high sensitivity type). Continued use in this condition may cause the airbag to inadvertently deploy due to strong road surface …
Mitsubishi KL-FP50JDR 1999–2003
Mitsubishi KL-FP50JGR 1999–2003
Mitsubishi KL-FP50KFXD 1999–2003
Mitsubishi KL-FP50KHX 1999–2003
Mitsubishi KL-FP50KLX 1999–2003
+27 more
The vent ring (with a vent valve to prevent liquid fuel from being drawn into the fuel vapor canister during operation) welded to the resin fuel tank has improper molding. Repeated expansion …
Honda Crossroad 1993–1998
In vehicles equipped with front fog lights sold as dealer-optional parts, an incorrect light switch was installed during fog light mounting. When the right turn signal is activated with both the low-beam …
Nissan Serena 2005
Injuries — Risk of injury. The front suspension lower ball joint may wear and become loose; in extreme case ball joint may separate from knuckle and cause loss of steering control.
The attachment clip securing the connection between the brake pedal and pushrod may not be properly installed on some vehicles. Repeated brake operation could cause the connection to separate, potentially resulting in …
キャデラック DeVille 2003–2004
On vehicles equipped with a rear body, the stopper rear body mounting position is improper, resulting in insufficient clearance between the stopper rear body mounting bolt and the rear brake pipe on …
Isuzu Forward 2004
On vehicles equipped with a rear body, the rear brake pipe clamp was not installed, causing the brake pipe to vibrate and potentially interfere with the stopper rear body mounting bolt. Continued …
Isuzu Forward 2004