Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 40 of 355
The lock plate in the latch section of the third-row seatback may have been incorrectly assembled due to inadequate work instructions. This can result in incomplete seat fixation, causing the seat to …
The transmission control module software is inadequate. During deceleration, downshifting from 3rd to 2nd gear may fail to engage 2nd gear. This may result in the transmission shifting to neutral and warning …
In the outrigger apparatus of aerial work vehicles and pole-digging/setting vehicles, the manufacturing process of the extension cylinder is inappropriate, resulting in machining defects in the cap-fixing screws of the cylinder tube. …
In the lower arm of the left front wheel, improper assembly work during vehicle manufacturing has resulted in some ball joints not being fixed in the specified position. Consequently, the ball joint …
The impeller (resin-molded fan wheel) in the fuel pump may swell and deform due to improper manufacturing when exposed to fuel. As a result, the impeller can contact the pump housing, causing …
Due to inadequate manufacturing control, some tires have non-uniform vulcanization process quality. Under driving loads, carcass damage can occur, resulting in air leakage or tread separation, which in worst case may impair …
Due to inappropriate material selection in the fuel hose, thermal degradation may progress. This can result in decreased sealing integrity at connection points, potentially causing fuel leakage.
The Electronic Stability Program (ESP) control program is inappropriate. If the vehicle operates in a manner that causes the ESP to intervene shortly after starting, the system may incorrectly self-diagnose as faulty. …
The engine control computer (ECU) has an improper control program that may misinterpret momentary crankshaft reversal during engine stop position control in EV driving or regenerative braking as an anomaly, causing the …
On large trucks and buses, the emission control device control module (ACM) is improperly configured, causing the diagnostic sequence that confirms sensor failure (from engine start to stop, and until the next …
In some vehicles subject to Notification No. 5109 dated March 3, 2022, the ACM (Evaporative Emission Control System control module) control program has not been correctly reprogrammed due to improper work instructions …
In the engine camshaft, due to a heat treatment machine programming adjustment error, the exhaust cam heat treatment was improper, resulting in insufficient surface hardness in some units. This causes abnormal wear …
The control program of the Battery Energy Control Module in the electric motor power supply is inadequate, which may prevent temperature anomaly monitoring during thermal overload conditions of the battery pack assembly. …
The diesel engine exhaust gas recirculation (EGR) module has insufficient durability consideration, causing coolant leakage due to age degradation. When this occurs, soot contained in exhaust gas mixes with coolant and accumulates …
In the parking brake system of excavators and loaders, rainwater ingress protection for the parking brake valve was insufficiently considered. Rainwater may enter through gaps in the connector lead wire insertion area. …
The oil strainer installed on the oil supply line to the turbocharger has an excessively small mesh size, which can cause oil deposits to accumulate on the strainer. As the vehicle is …
During manufacturing of the battery cell monitor electronic circuit, an internal connector may not have been installed correctly. This could cause the high-voltage battery to shut down without illuminating the warning light, …
In engine-powered forklifts, the fuel return line that returns excess fuel to the tank has inadequate design, resulting in insufficient strength in some units. Repeated engine start/stop cycles in this condition can …
In the Vehicle Control Module of e-POWER vehicles and electric vehicles, the motor output control program was inadequately evaluated during development, resulting in deficiencies in the program. Consequently, unintended acceleration may occur …
In the engine room harness, inadequate verification during development resulted in deficiencies in harness routing. When the tip of the engine control unit mounting bolt is positioned at the slit of the …
In the blowby hose that directs blowby gas from the generator engine to the intake manifold, the protector dimensions are insufficient to prevent hose surface degradation due to inadequate evaluation during development. …
The right-side headlight may not satisfy safety standards for optical axis alignment because inspection and adjustment were performed with improper settings on the vehicle manufacturing facility's optical axis adjustment equipment.
In the backup camera, improper fixation of electrical wiring causes the wiring to move when the rear gate is closed or due to vehicle vibration during driving, resulting in sliding contact between …
During vehicle manufacturing, improper equipment settings in the electrical components inspection process resulted in failure to verify readability of software information in certain electrical components.
Tailgate gas dampers may have internal seal damage due to improper processing equipment settings. This can result in gas leakage from the damper, causing increased resistance in tailgate operation, and in worst …
In vehicles that were prototyped and modified as hydrogen fuel cell vehicles, improper design of peripheral components related to the modification results in: (1) absence of electrical wiring to the brake fluid …
In vehicles prototype-modified as hydrogen fuel cell vehicles, improper design of peripheral components related to the modification causes: (1) Absence of electrical wiring to the brake fluid level sensor in the braking …
In vehicles that were prototyped and modified as hydrogen fuel cell vehicles, the design of peripheral components related to the modification is inappropriate, resulting in: (1) Absence of electrical wiring to the …
The current rectification module in the voltage conversion device (DC-DC converter) has an improper internal component structure. When the module fails during use due to manufacturing variations and other factors, a short …
In the hydraulic hose for wing door opening and closing operations on wing-type vehicles, there were deficiencies in the management of manufacturing fixtures, resulting in some terminal fittings attached to the hose …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.