Before you buy, check it isn't under a dangerous recall.

The driver and front passenger seat belt pretensioners have defective igniter-containing tubes due to inadequate manufacturing control. During deployment in a crash, these pretensioners cannot retract slack from the seat belt, potentially …

The rear lighting module mounted on the tailgate may have an incorrectly specified unit installed. As a result, the turn signal indicator and emergency flasher may fail to blink.

Manufacturing defects in high-voltage battery cell modules may cause high-voltage battery malfunction. In rare cases, the high-voltage battery may discharge, potentially leading to fire in the worst scenario.

Due to a manufacturing defect, the pressure spring required for the power-folding function of the third-row seat may not be correctly installed or may be completely missing. Consequently, the seat backrest may …

In medium-duty trucks, the horn body material is inappropriate. Water containing de-icing agent entering through gaps in the inner fender can contact the horn, causing internal corrosion. As a result, the horn …

The parking brake lever on agricultural chemical sprayers has insufficient strength, resulting in improper engagement between the hook and gear, which may cause the hook to deform. Continued use in this condition …

The turn signal unit is defectively designed. When the turn signal malfunctions due to disconnection or other faults, no warning is displayed to the driver. This may result in the driver continuing …

In agricultural tractor meter panel wiring harnesses, inadequate protective routing per wiring harness drawings allows contact between the harness and the brake pedal return spring mounting plate. Vibration during operation causes harness …

In the camera for the preventive safety function (Smart Assist), adhesive process control of the camera-fixing bracket to the windshield glass was inadequate, resulting in some units with insufficient adhesive strength. Consequently, …

Certain vehicles have insufficient fastener verification at the manufacturing plant. Consequently, insufficiently tightened bolts may loosen during operation, causing various components to detach. Additionally, vehicle running stability may be compromised.

Due to improper manufacturing processes for the track rod on the front axle, some track rod ends lack the required slit machining. Consequently, even when the track rod end is tightened with …

Due to improper manufacturing processes of the track rod on the front axle, some track rod ends lack the required slit. This can result in insufficient clamping fixture engagement with the ball …

The steering gear boot attachment seal is inadequate, and the air conditioning drain hose is positioned directly above it. Consequently, air conditioning condensation water drips onto the attachment area and may enter …

The engine ECU software contains an inappropriate diagnostic program for low-pressure fuel pressure. Under normal low-pressure fuel conditions, the system may incorrectly detect a malfunction, causing the engine warning light to illuminate …

In electrical systems of wheel cranes and similar equipment, cable terminal connectors connected to high-current fuses have been selected inappropriately, causing interference between the cable terminal connectors and parts of the fuse …

The inflator (inflation device) of the driver-side airbag may experience degradation of the gas propellant when subjected to repeated temperature changes in high-humidity environments. Consequently, the inflator housing may rupture upon airbag …

The horn bracket mounting bolts at the vehicle front are improperly installed. Vibration during driving may loosen these bolts, causing the horn bracket assembly to shift from its specified position. Continued driving …

In the braking system, brake fluid may leak from the hydraulic seal section on the brake booster side of the master cylinder into the brake booster. If the brake fluid in the …

The electric handle lock mechanism has improper lock pin positioning and insufficient component strength. When the handle lock is engaged, if the lock pin fails to enter the lock hole, impact forces …

The C-pillar mounting bracket in the roof lining has an improper design, which may result in insufficient bracket securing. Consequently, if a side airbag deploys during a collision or similar incident, the …

In the brake fluid leak warning device, due to inappropriate control programming, the low fluid level warning light does not illuminate even when brake fluid level drops below the specified value, which …

Third row seat belt buckle assembly: During manufacturing, the rivet securing the buckle to the mount bracket may not be formed properly. In such cases, occupants may not be restrained adequately during …

The ambient light sensor used in the automatic headlamp system outputs voltage lower than the specified value in bright environments, preventing the body control module from correctly determining ambient light conditions, which …

During manufacturing, impact testing used to verify fuel pump connector seating may have dislodged the rollover valve inside the fuel tank. If the valve is missing and the vehicle rolls over in …

In the manufacturing process of replacement reduction gears, the parking lock assembly process was improper, resulting in some units being assembled with non-conforming parking rods. Consequently, the parking lock may not engage, …

In the hybrid system, due to an inappropriate control program, temporary slippage may occur in the transaxle input damper during rapid acceleration and similar conditions, causing the warning light to illuminate. In …

(1) In curtain shield airbags, improper assembly work at the vehicle factory has resulted in some units where the deployment assist strap is not installed in the correct position. As a result, …

(1) In curtain shield airbags, some units have deployment assist straps that are not assembled in the correct position due to improper factory assembly procedures. As a result, the airbag may not …

On the back door hinge, due to inadequate work and inspection instructions in certain manufacturing processes, some fastening nuts on the vehicle body were tightened with excessive torque exceeding the specified value. …

Due to improper programming in the instrument cluster, the brake booster warning light fails to illuminate when the brake booster malfunctions. After country-specific message confirmation, an incorrect warning light illuminates, potentially failing …