Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 120 of 175
In large double-cab vehicles, the power steering hose routing is improperly configured, such that the tire may contact the hose when passing over curbs or similar obstacles with the steering turned to …
Right-hand drive vehicles have airbag control computers programmed with left-hand drive settings at manufacture. In side-impact collisions on the right side (driver side) when no passenger is seated in the front passenger …
The nut fastening process connecting the parking brake and transmission was improper, resulting in insufficient tightening on some units. Consequently, the nut may loosen and catch on the transmission output shaft, potentially …
The grip (non-slip handle) attached to the handlebar in the steering assembly may have inadequate adhesion. This could cause the grip to separate from the handlebar, potentially resulting in loss of control …
Due to improper programming in the airbag control computer, side airbags and curtain airbags may not deploy during side-impact collisions.
Some pipe components located above the fuel pump are made of inappropriate material. Due to aging and environmental conditions, cracks may develop in these pipe sections. In the worst case, fuel leakage …
In diesel engine fuel injection pumps, the return-to-tank fuel eye bolt (pipe fitting bolt) lacks sufficient clamping force. Engine vibration causes repeated interference with the protective material of an adjacent rubber hose, …
Some front wheel hub bearings have excessively tight fastening bolts at the knuckle connection, causing deformation of the bearings. Continued use in this condition may damage the bearing interior, producing abnormal noise …
The nut fastening the pipe connected to the fuel supply pump (supply pump) of the fuel injection system lacks sufficient tightening force, resulting in inadequate seal integrity in some units. Continued operation …
The pipe nut connecting to the fuel supply pump (supply pump) of the fuel injection system has insufficient fastening torque, resulting in inadequate seal integrity in some units. Continued use in this …
Improper assembly of the nylon tube supplying air to the air cylinder for the swing door opening/closing mechanism on large tour buses can result in tube disconnection and air leakage. This may …
Improper assembly of nylon tubing that supplies air to the swing door open/close air cylinders on large tour buses can result in tube disconnection and air leakage. This may cause the door …
Some coupling (fifth wheel) release handle pin attachment holes are oversized. Continued use in this condition may result in pin detachment, potentially causing trailer separation.
Certain work lights (non-driving lights) used during operation lack a device enabling the driver to confirm illumination status from the driver's seat, potentially failing to comply with safety standards.
Certain work lights (non-running lights) lack a device to confirm illumination status from the driver's seat, potentially failing to comply with safety standards.
The excavation work device hose routing is improper, causing contact with the brake air hose in some cases. If operation continues in this condition, vibration of the vehicle body may cause the …
The fuel pump unit mounting area on the fuel tank has improper drilling, resulting in some units with oversized holes or sharp protrusions at the mounting point. Continued use may cause cracks …
In the steering gear of the steering system, pinion shaft bearings may not be installed during the manufacturing process. As a result, the pinion shaft may not be securely retained, and in …
On driver and front passenger door openings equipped with intelligent key, some exterior handles have oversized dimensions. When the door is opened, the handle may catch and fail to return to its …
In the driver and front passenger door openings of vehicles equipped with Intelligent Key, some exterior door handles have oversized dimensions. When the door is opened, the handle may catch and fail …
Inadequate waterproofing in the heating heat exchanger housing allows moisture containing de-icing salt to infiltrate, causing electrical leakage at the blower motor harness connector. Continued operation can cause the connector to overheat …
Inadequate waterproofing of the heating exchanger storage box allows moisture containing de-icing agent to enter, causing leakage current at the blower motor harness connector. Continued operation may cause the connector to overheat …
The cruise control cancel switch mounted on the master cylinder has an inadequate seal structure inside the switch. Brake fluid can leak and contact internal electrical terminals, causing corrosion of the contacts. …
Some units have insufficient fastening torque on the left rear wheel mounting bolts and nuts. Continued use in this condition may result in left rear wheel detachment in the worst case.
Some air conditioning compressor electromagnetic clutches have insufficient contact surface area on the engagement face with inadequate margin. When the compressor drive belt tension is excessively adjusted and the vehicle operates continuously …
When moving a crane-equipped cart with the crane attachment installed within a work site, stress exceeding the fatigue limit of the material may occur in the third axle (spindle) section. If use …
The engine control computer's idle speed control program is improper. When the air conditioner is operated in high ambient temperatures and the vehicle continues high-speed driving at a constant speed, engine RPM …
The vacuum pipe supplying negative pressure to the brake booster has an inappropriate shape, causing interference with the cabin. Continued use may result in the pipe fracturing due to vibration during operation, …
Due to improper engine control computer programming, when the accelerator pedal is depressed significantly during high-speed cruising with cruise control engaged, such as during overtaking, the system may misdiagnose a throttle malfunction, …
The seal section inside the shock absorber in the rear suspension may be damaged, allowing shock absorber oil to leak. This results in degraded damping function and, in worst case, may compromise …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.