Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 157 of 175
The parking brake ratchet lever has an improper geometry, resulting in shallow engagement. Continued use in this condition may cause ratchet wear from lever operation, leading to disengagement of the ratchet and …
In the lighting equipment, the exhaust pipe outlet position near the rear bumper is improperly located. The rubber retaining ring for the exhaust pipe may elongate over time, causing the outlet direction …
Certain air-operated parking brake wheel cylinder boots in the primary braking system have insufficient air-tightness. Continued use in this condition allows water ingress into the boot, causing the wedge guide sliding surface …
In the running gear, the wheel hub bearing geometry of the left and right rear axles is inappropriate, causing the seal O-ring to not seat properly in some vehicles. Continued use in …
In air suspension equipped vehicles, the brake system's air compressor piston ring has an inappropriate shape, causing increased lubricating oil leakage. Continued operation in this condition causes the lubricating oil to carbonize …
In the fuel system, the metal filter at the tip of the fuel pump inside the fuel tank contacts the inner wall of the fuel tank. When water accumulates in the tank, …
In the fuel system, certain fuel hoses are made of inappropriate material. Continued use in this condition may cause material degradation, leading to pinhole formation, fuel leakage, and potentially fire.
In the fuel system, improper installation of the fuel pump mount may result in gasket damage during assembly. Fuel may leak from the damaged gasket area, potentially leading to fire in severe …
In the front-wheel braking system, the brake hose is retained improperly and may interfere with the front fork. Continued use in this condition can damage the hose, causing brake fluid leakage and …
In the suspension damper system, some vehicles lack the upper bolt securing the right front shock absorber bracket to the vehicle frame. Continued operation in this condition allows the bracket to deform …
In the front-wheel braking system, the rubber grommet of the cable holder securing the speedometer cable near the brake pipe has an inappropriate structure and shape. Vibration of the cable causes the …
In the fuel system, some fuel hoses have the carburetor-side securing clamp installed at an incorrect position. If operation continues in this condition, vehicle vibration may cause the hose to detach, potentially …
The Active Stability Control System (ASC) braking behavior control function contains a gas-charged accumulator in the ASC hydraulic unit with insufficient diaphragm durability. Continued use may allow enclosed gas within the accumulator …
In the electronically controlled primary braking system, foreign material may become lodged in the brake actuator (hydraulic control unit) due to manufacturing defects, causing hydraulic pressure to drop. Due to inappropriate control …
The crankshaft timing belt guide plate mounting surface on the engine has been machined improperly, resulting in insufficient mounting surface area on some units. Continued operation in this condition may cause the …
In the engine, bolts securing the crankshaft pulley to the crankshaft were not adequately lubricated, resulting in insufficient clamping force in some cases. Continued operation in this condition causes bolt loosening and …
In the braking system, the connector joining the hose between the brake master cylinder and brake fluid reservoir has inadequate strength. Continued use in this condition may cause cracks to develop in …
In the engine, improper manufacturing process control of the crankshaft has resulted in residue adhering to the threaded portion of the pulley bolt mounting location on some units. This causes insufficient clamping …
The engine may have excessive timing belt tension, causing the crankshaft to resonate and loosen the crankshaft pulley mounting bolts. In the worst case, the accessory drive crankshaft pulley may slip, disabling …
The passenger-side airbag unit has inadequate grounding. In low-humidity conditions, static electricity accumulates and, if the vehicle continues to be used in this state, discharge may occur within the airbag unit, potentially …
The driver-side door lock mechanism mounting screws may be insufficiently tightened, causing the screw to loosen and fall out. This results in incomplete door latch engagement, which may cause the door to …
In the braking system, the bolt securing the parking brake shoe retention bracket is of improper length, resulting in insufficient tightening. Continued use in this condition may cause the bolt to loosen …
The windshield wiper features an improperly designed electrical contact structure in the blade position control circuit, which is integrated into the plastic gear cover. Continued use in this condition may cause the …
The windshield wiper for the front glass has an improperly designed electrical contact structure in the blade position control circuit built into the plastic gear cover. Continued use in this condition can …
In the braking system, improper machining of the anchor bracket bolt mounting section causes loosening of the bracket attachment. Continued use in this condition may result in bolt fracture, which could damage …
In the electrical system, the meter wiring routing is improper. If continued in this condition, when the handlebar is turned fully left, the wiring may contact and be damaged by the fixing …
Aluminum air tanks that supply compressed air to the braking system may develop surface cracks due to improper heat treatment of the tanks. Continued use in this condition can allow cracks to …
The parking brake automatic stroke adjustment mechanism is defectively designed with insufficient engagement of the locking pawl. Continued use in this condition may cause the pawl engagement to disengage, increasing brake cable …
In the fuel system, foreign material contamination during manufacture of the fuel return hose (which returns fuel from the fuel injector to the tank) has resulted in insufficient hose strength in some …
The fuel hose routing in the right cylinder fuel line of the engine is improper. Continued use in this condition may cause the fuel hose and fuel pipe to interfere due to …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.