Before you buy, check it isn't under a dangerous recall.

The Electronic Stability Program (ESP) control program is inappropriate. If the vehicle operates in a manner that causes the ESP to intervene shortly after starting, the system may incorrectly self-diagnose as faulty. …

The control program of the Battery Energy Control Module in the electric motor power supply is inadequate, which may prevent temperature anomaly monitoring during thermal overload conditions of the battery pack assembly. …

The diesel engine exhaust gas recirculation (EGR) module has insufficient durability consideration, causing coolant leakage due to age degradation. When this occurs, soot contained in exhaust gas mixes with coolant and accumulates …

In the parking brake system of excavators and loaders, rainwater ingress protection for the parking brake valve was insufficiently considered. Rainwater may enter through gaps in the connector lead wire insertion area. …

In engine-powered forklifts, the fuel return line that returns excess fuel to the tank has inadequate design, resulting in insufficient strength in some units. Repeated engine start/stop cycles in this condition can …

In the engine room harness, inadequate verification during development resulted in deficiencies in harness routing. When the tip of the engine control unit mounting bolt is positioned at the slit of the …

In the blowby hose that directs blowby gas from the generator engine to the intake manifold, the protector dimensions are insufficient to prevent hose surface degradation due to inadequate evaluation during development. …

In vehicles that were prototyped and modified as hydrogen fuel cell vehicles, improper design of peripheral components related to the modification results in: (1) absence of electrical wiring to the brake fluid …

In vehicles prototype-modified as hydrogen fuel cell vehicles, improper design of peripheral components related to the modification causes: (1) Absence of electrical wiring to the brake fluid level sensor in the braking …

In vehicles that were prototyped and modified as hydrogen fuel cell vehicles, the design of peripheral components related to the modification is inappropriate, resulting in: (1) Absence of electrical wiring to the …

The current rectification module in the voltage conversion device (DC-DC converter) has an improper internal component structure. When the module fails during use due to manufacturing variations and other factors, a short …

On vehicles equipped with front air suspension, the anchor bolts securing the air spring on the front axle have been tightened to improper torque specifications. Due to running vibration and other factors, …

In the braking system, the front brake hose attachment to the vehicle body may be improperly installed and not positioned correctly. Consequently, the hose may contact the hose guide edge, and continued …

In route-specification large buses, the harness within the distribution box installed on the upper right side of the driver's seat interferes with the rear upper edge of the air conditioning control unit …

The control program for the lane guidance function of the driving assistance system (part of the adaptive cruise assist system) contains defects due to insufficient evaluation during development. Consequently, the system disengagement …

The collision mitigation brake in the driver assistance system has control programming that causes it to react overly sensitively in certain situations, which may result in the system misidentifying roadside structures and …

In the engine, the right-side crankcase cover has improper manufacturing process, causing paint adhesion on the sealing plug press-fit section. Due to engine heat, the sealing plug retention force decreases, and continued …

The control program for the driving assistance system Travel Assist has deficiencies due to insufficient evaluation during development. Consequently, the system deactivation operation upon steering hand-off detection does not comply with safety …

In passenger doors, improper manufacturing control of the outer door handle may result in the membrane filter not being correctly installed. Moisture can subsequently penetrate the electronic circuit, potentially causing unintended door …

The strut mount on the front suspension may be deformed due to inadequate equipment management during the press-nut manufacturing process. As a result, some bolt connections between the vehicle body and strut …

In the fuel system, insufficient corrosion resistance evaluation at the design stage has led to galvanic corrosion between dissimilar metals: the fuel pipe (aluminum) between the left and right fuel tanks and …

Due to inadequate process control during front wheel assembly, certain bolts and nuts may have insufficient fastening torque. Consequently, these fasteners may loosen under running vibration, potentially causing abnormal noise, decreased running …

① The rear brake lamp switch has an inadequate seal design. Foreign matter entering through the seal can accumulate on electrical components and cause corrosion over time, potentially causing the switch to …

The waterproof cap for the rear door has not been installed due to improper work instructions. High-pressure washing and similar operations may cause water ingress to the electrical wiring. Continued use in …

The camera for the preventive safety function (Smart Assist) is affixed to the windshield glass via a bracket. Inadequate adhesive process control results in weak adhesion on some units. During use, the …

Certain tires have non-uniform bead thickness due to inadequate manufacturing control. This prevents uniform contact between the bead and wheel rim, causing air leakage. Depending on operating forces, rapid air loss may …

The air conditioning evaporator drain hose may be improperly assembled, allowing condensation to leak into the vehicle interior. This can result in water accumulation beneath the floor, causing corrosion and electrical short …

Due to an improper control program in the voltage converter, temporary communication failures between the server and diagnostic scanner (scan tool) during connection cause the converter to incorrectly diagnose a fault and …

Heavy-duty trucks equipped with 6R20 engines have improper engine harness assembly, causing the harness to make strong contact with the harness-fixing bracket. Engine vibration causes wear and damage at the bracket contact …

Front ABS sensor harness bracket bolts on the steering knuckle may not be tightened to the specified torque due to improper assembly during vehicle manufacturing. Continued use could result in bolt loosening …