Before you buy, check it isn't under a dangerous recall.

The coolant pump installed on diesel engines has inadequate bearing seal design, allowing coolant to enter the negative pressure circuit that controls component operation. This causes malfunction of negative pressure circuit components, …

The brake hose bracket welding to the vehicle body is partially defective. The bracket may detach, causing the brake pipe to contact the vehicle body due to running vibration, resulting in noise. …

The bolt securing the ABS pulser ring on the rear brake may loosen due to insufficient fastening. This can cause ABS system malfunction and illuminate the ABS warning light. In the worst …

The mounting bolts for the fuel pipe attached to the engine have an improperly designed tightening torque specification. Due to driving vibration and similar factors, these bolts may loosen. This can result …

The attachment bolts for fuel pipes mounted on the engine have improper design torque specifications, which may cause the bolts to loosen due to driving vibration and other factors. This can result …

Brake calipers have inadequate metal surface treatment on the piston sliding surfaces, which can cause corrosion from de-icing salts. This corrosion creates resistance in the sliding surfaces, resulting in poor piston retraction …

In the driver and passenger seat airbag (SRS) wiring, improper processing of the wire insulation may cause insulation fibers to become entangled in the seat adjustment shaft during seat adjustment. This may …

The retaining ring was not installed on the gear portion of the axle on agricultural chemical spraying vehicles, resulting in improper gear mesh engagement. This causes vibration and abnormal noise. Continued use …

Hub bolts for tire attachment may loosen due to repeated sharp turns or hard braking. Continued operation in this condition may result in abnormal noise and, in the worst case, tire detachment.

In vehicles equipped with manual transmissions, the engine control computer's ignition timing control program is improper. When the throttle is fully closed and the clutch lever is gripped with a small grip …

In PHEV vehicles, due to improper software in the engine control unit, after recovery from protection mode triggered by multi-cylinder misfire, the throttle valve opening and intake valve lift become fixed at …

The engine control unit program is improper. During engine warm-up, when the engine remains at idle, fuel reduction control activates to clean exhaust emissions, causing the air-fuel mixture entering the combustion chamber …

The engine control unit program is improper. When the throttle is held slightly open, it excessively increases fuel, causing the air-fuel mixture in the combustion chamber to become rich. The system then …

The Engine Control Unit (ECU) program is inappropriate. When the throttle is held slightly open, the ECU incorrectly recognizes the throttle as closed and reduces fuel supply, causing the air-fuel mixture entering …

The cab auxiliary heater wiring is mounted at an improper position, causing interference and abrasion with the cab auxiliary heater bracket. In the worst case, wiring damage may cause the cab auxiliary …

In the brake system, brake fluid may leak from the hydraulic seal on the brake booster side of the master cylinder into the brake booster. If the primary circuit brake fluid is …

Improper plastic manufacturing of the PCV heater causes irregularities in the insulation of the positive temperature coefficient (PTC) heater element. Over time, the PTC heater element may short circuit but is not …

Improper mounting position of cab auxiliary heater wiring causes interference and rubbing against the cab auxiliary heater bracket. In the worst case, wiring damage may prevent the cab auxiliary heater from operating …

Cab auxiliary heater wiring is mounted at an improper position, causing interference and abrasion with the cab auxiliary heater bracket. In worst-case scenarios, wiring damage may cause the cab auxiliary heater to …

The wiring mounting position of the cab auxiliary heater is improper, causing interference and abrasion with the cab auxiliary heater bracket. In the worst case, wiring damage may cause the cab auxiliary …

The cab auxiliary heater wiring is mounted at an inappropriate position, causing it to interfere and chafe against the cab auxiliary heater bracket. In the worst case, wiring damage may cause the …

The axle bolts securing the hub on the rear axle were tightened improperly, causing bolts to loosen due to driving vibration and other factors, resulting in component rattling and abnormal noise. If …

In the PDA (Proactive Driving Assist) of the driving support system, due to an inappropriate control program, if the brake pedal is operated during deceleration control by the PDA, the brakes may …

In the front-wheel braking system, insufficient component management during assembly may result in brake discs of incorrect dimensions being installed. In such cases, the system may not comply with the technical requirements …

Due to improper fuel tank manufacturing, the fuel pipe connector mounted on the tank top may not be correctly seated. Consequently, the connector may detach due to driving vibrations or other factors, …

The impeller (resin-molded rotor) of the low-pressure fuel pump may swell and deform due to improper molding conditions resulting in reduced resin density, causing swelling when exposed to fuel. This can cause …

In the braking system of electric forklifts, due to inappropriate programming of the control controller, the backup braking function may fail to operate during low battery voltage error conditions, potentially preventing safe …

In the powertrain, some gearboxes have insufficient oil fill due to equipment failure during manufacturing. This may cause clutch slippage and, in worst cases, display a warning message and interrupt power transmission. …

In the power transmission system, some gearboxes have insufficient oil fill due to equipment failure at the production facility. This can cause clutch slippage and, in worst case, display warning messages and …

The coolant pump installed in diesel engines has improper bearing seal design, allowing coolant to infiltrate the vacuum circuit under controlled operation. This causes malfunction of vacuum circuit components, resulting in illumination …