Before you buy, check it isn't under a dangerous recall.

The rubber sleeve installed on the brake booster has an inadequate design, allowing moisture that enters the gap between the booster housing and sleeve to remain trapped for extended periods without draining. …

In the engine's high-pressure fuel piping, inadequate process control during assembly has resulted in fine particles being trapped in the seal between the fuel rail and injector. During use, this seal can …

Some units may be susceptible to accelerated corrosion and fatigue of the steering shaft. Continued use in this condition may result in steering shaft fracture, loss of driving stability, and potential inability …

In the electrical system of rotary snow removal vehicles, improper wiring fastening causes alternator and ground wiring to chafe against wiring clamps during driving vibration, resulting in insulation damage. Continued use may …

In the braking system of a rotary snow removal vehicle, the mounting section shape of the air compressor pulley is inappropriate. Due to vibration during operation, the pulley fixing nut may loosen …

In the running gear of rotary snow removal vehicles, the hub bolts for wheel attachment have inadequate strength and may fracture. Hub bolts and hub nuts can then fall into the brake …

Insufficient layout validation during design may allow a portion of the rear wheel arch liner (wheel house cover) to contact the rear brake pad position sensor cable through vibration, potentially damaging the …

In front doors, improper settings of the door latch and striker may cause the door latch to deform when the side airbag deploys during side-impact collision. In the worst case, the engagement …

In medium-duty trucks, due to improper ABS ECU software, rapidly turning the ignition key at engine startup causes the brake pedal power supply to be cut off when a brake pedal power …

Due to improper onboard charger circuit board connections and inadequate EVCCU (Electric Drivetrain Supervisor ECU) software, temporary voltage fluctuations may occur in the onboard charger, causing the EV system to be misdiagnosed …

The data bus diagnostic interface mounted beneath the rear seat may experience short circuits due to moisture from liquids spilled on the rear seat or water ingress during heavy rain or deep …

Aluminum tank lorries equipped with cargo discharge pumps have insufficient pump bracket rigidity due to design defects, causing cracks in piping connected to the pump. Continued use in this condition may result …

The SRS (Supplemental Restraint System) control unit may not be securely fastened due to improper installation during manufacturing. Consequently, airbags may not deploy properly during collision, or sudden deployment may occur if …

The coolant pump installed on diesel engines has an improperly designed bearing seal, which allows coolant to enter the negative pressure circuit that is normally sealed. This can cause malfunction of components …

In the braking system of agricultural tractors, improper design of the hydraulic circuit allows air to enter the hydraulic circuit. Continued use in this condition may result in degraded brake performance.

Some semi-trailers are equipped with brake chambers that cannot be disassembled for service brake maintenance. This prevents replacement of scheduled internal service brake components as specified in the maintenance procedures.

In some vehicles, the center of gravity is positioned excessively high during cargo box installation on the chassis. This may cause the maximum lateral stability tilt angle to fall below standard specification, …

The front-wheel braking system may have brake discs of incorrect dimensions installed due to inadequate component management during assembly. In such cases, the system may not comply with the technical requirements of …

In snow removal vehicles, the alternator wiring routing for the work engine is improper, causing the wire insulation to melt due to radiant heat from the engine exhaust manifold. If operation continues …

The engine cover mounted on the upper portion of the engine has insufficient strength at its attachment points. Depending on vehicle age and usage conditions (extremely aggressive driving or off-road driving on …

The engine cover mounted on top of the engine has insufficient attachment strength. Depending on vehicle age and operating conditions (particularly aggressive driving or off-road use on poor surfaces), the cover may …

In large tractors, the trailer-side brake lamp circuit is improperly designed, which may cause diodes in this circuit to burn out when the brake lamp is illuminated. As a result, the trailer-side …

On medium-duty trucks, improper rear suspension design can cause interference between the rear wheel brake chamber and frame when traversing steps or similar obstacles, potentially resulting in brake chamber damage and reduced …

In heavy-duty trucks, improper manufacturing processes in the parking brake air pressure sensor may leave conductive foreign matter on the sensor circuit board, causing short circuits or malfunction. This can result in …

In the air pressure control system (APS), some units have inadequate design of the air dryer regeneration control valve, preventing proper air pressure sealing. This causes air leakage, resulting in warning light …

①Vehicle Stability Control (VSC) system: Due to inappropriate control program logic, when the system restarts after being stopped with the brake pedal held depressed while VSC is in the OFF state, the …

① In the Vehicle Stability Control (VSC) system, due to inappropriate control program logic, when the system restarts after shutdown while the brake pedal is held down with VSC disabled, the function …

In the Air Pressure Control System (APS), some units have an improperly designed air dryer regeneration control valve that cannot maintain air pressure integrity. This may result in air leakage, illumination of …

In the air pressure control system (APS), the air dryer regeneration control valve has an inadequate design, which may prevent maintaining air pressure integrity. This can cause air leakage, warning light illumination, …

In the air pressure control system (APS), some vehicles have improper design of the air dryer regeneration control valve, preventing adequate air pressure sealing. This causes air leakage, resulting in warning light …