Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 60 of 175
The fuel tank vent pipe connecting to the charcoal canister has an improper shape. When the fuel tank is full and the vehicle is parked on the sidestand, fuel sloshing inside the …
In rotary snow removal equipment mounted on excavator-loaders, improper battery cable installation instructions can cause the cable to interfere with hydraulic hoses due to vibration during operation, potentially damaging the hose covering. …
In wheel crane braking systems, improper manufacturing of brake calipers results in low cap fastening torque. During brake actuation, hydraulic pressure may cause the cap to loosen. Continued operation in this condition …
In articulated buses, improper edge finishing of the wiring securing bracket in the power distribution box behind the driver's seat may cause wiring to interfere with the bracket's edge. If use continues …
In semi-automatic hydraulic clutches, insufficient evaluation of vibration resistance at the clutch hydraulic pipe connection has resulted in engine vibration causing the connection retention pin to detach. This can damage the pipe, …
In the electrical system, the routing of the regulator wiring is improper in some vehicles, causing the wiring to contact the regulator bracket. As a result, the insulation may be damaged by …
The ESP (Electronic Stability Program) control unit has an inadequate control program, which fails to manage tire slip during rapid acceleration on wet road surfaces, causing severe vibration in the drivetrain and …
In the front air suspension, improper manufacturing of the air bellows can cause the support ring (retaining bracket) to detach due to vibration during driving, resulting in air bellows damage. This may …
The power distribution module's circuit board was coated with moisture-resistant material while retaining unnecessary solder residue from manufacturing. During use, cracks can develop in this coating. In high-humidity environments, this allows fine …
In large trucks, the clamping section assembly of the front axle tie rod end on the front two-axle vehicle is improper, resulting in insufficient fastening torque on the mounting bolt. If the …
In large trucks, the battery fixed plate has an improper shape, causing the power cable to interfere with the edge of the fixed plate when attached to the battery terminal. Continued use …
Driver-side airbag inflators may have inadequate moisture protection of the gas generant. Under high-humidity environments with repeated large temperature fluctuations, the gas generant can degrade. This may cause inflator container rupture during …
In the Electronic Stability Program (ESP), due to an inadequate control program in the ESP control unit, if communication between the unit and the driver assistance system is lost while cruise control …
The inflator (inflation device) of the front passenger airbag has inadequate moisture prevention for the gas generant. Repeated cycles of temperature and humidity changes may cause degradation of the gas generant. As …
On vehicles equipped with a glass roof, improper work instructions during glass roof installation result in insufficient adhesive strength. The adhesive bond of the roof may delaminate due to driving vibration and …
Due to improper diagnostic tool configuration during servicing, some vehicles have incorrect programming installed in the restraint control unit that governs airbag deployment. This causes the airbag deployment control threshold to be …
Due to improper design of the ignition key module in the starting system, some units lack sufficient force to maintain key position. When a key holder or similar accessory is attached to …
Due to improper design of the ignition key module in the starting system, the ignition key cylinder may move from the ON position toward the ACC position when the driver's knee or …
In the brake booster vacuum hose, improper assembly work has resulted in foreign material adhering to the inner surface of some hoses. If operation continues in this condition, the check valve inserted …
Improper manufacturing of the front suspension frame can result in corrosion of the lower arm mounting bracket due to corrosive substances such as salt water. Continued use in this condition may allow …
In the fuel system, the resistor controlling the operating current of the electric fuel pump was selected inappropriately, causing premature degradation due to the operating current. If use continues in this condition, …
In the electric power steering system, improper manufacturing of the control unit has resulted in some units where the terminal portions of the internal circuit board are not properly welded. Continued use …
The on-board diagnostic system has inadequate programming for recognizing signals from the fuel system control module. When a malfunction occurs in the fuel pressure sensor, fuel temperature sensor, or fuel pump, the …
Hybrid vehicles equipped with a vacuum pump may experience internal component failure due to insufficient durability of internal parts. As internal components deteriorate during use, the pump loses the ability to generate …
In the electric parking brake, the brake control computer's open-circuit detection program is inappropriate. If the brake is not operated (engaged or released) for an extended period, oxide film forms on the …
In the power transmission system, the fastening structure of the belt-drive pulley is inadequate, which may cause the pulley fastening nut to loosen during operation. This can result in the pulley contacting …
In the hydrostatic transmission of a combine harvester, the structure of the emergency operation levers for turning and straight travel is inadequate, allowing rainwater and other moisture to seep into the base …
In the two-stage airbag device on the driver's side, improper manufacturing of the inflator has resulted in some units where the second-stage gas generator is not filled to design specifications. Consequently, the …
In the driver and front passenger seat heaters, improper routing of electrical wiring in the heater switch may cause the seat heater to continue operating even after the engine is stopped while …
In the electronic stability program (ESP), improper manufacturing of the hydraulic pressure regulator (ESP block) that controls brake fluid pressure may prevent electronic control of brake fluid pressure adjustment. Consequently, the anti-lock …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.