Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 72 of 175
Due to inadequate manufacturing control, some fuel injectors in gasoline engines have holes in the filter mesh component. If foreign matter from the fuel line enters the injector interior, the injector will …
The cam that drives the high-pressure fuel pump and brake vacuum pump in the engine has insufficient strength due to improper manufacturing. Under high-load operation, the cam may fracture, preventing fuel pressurization …
In the front-wheel brake system, some brake hoses are installed in a twisted manner. As a result, during operation the affected hose may contact the radiator, and in the worst case, the …
The inflator (inflation device) in motorcycle airbags may experience propellant degradation due to repeated environmental temperature and humidity fluctuations. This can cause abnormal pressure rise within the inflator during airbag deployment, risking …
The inflator (inflation device) in two-wheel vehicle airbags may experience propellant degradation due to repeated cycles of environmental temperature and humidity change. Consequently, internal pressure in the inflator may rise abnormally during …
The propellant in the passenger-side airbag inflator may degrade due to repeated cycles of ambient temperature and humidity changes. This can cause abnormally elevated pressure within the inflator during airbag deployment, risking …
The inflator (inflation device) of the passenger-side airbag may experience propellant degradation due to repeated environmental temperature and humidity fluctuations. Consequently, upon airbag deployment, internal pressure within the inflator may rise abnormally, …
In the electronically controlled steering system (Direct Adaptive Steering), due to an inappropriate initialization program at startup, if the vehicle is parked with the wheels turned and the engine is then started, …
(1) In the electronic ignition switch, due to improper electrical circuit design, when the engine is shut down with main battery voltage depleted, inadequate voltage may not be applied to the switch. …
The inflator (inflation device) of the front passenger dual-stage deployment control airbag has inadequate moisture prevention of the gas generant, which may degrade due to repeated temperature and humidity changes. As a …
Air hoses assembled in the power transmission and braking systems may be improperly installed, causing the hose to detach from joint connections and leak air. This results in reduced air tank pressure …
The airbag controller's control program is defective. If the ignition switch is turned on again at specific timing after being turned off, the control program may be erased. This causes the airbag …
The parking brake cable assembly and retaining nut fastening are improper. Repeated parking brake operation during use may cause the retaining nut to loosen. If operation continues in this state, the retaining …
The steering hydraulic pump has improperly selected bolts for attaching the split flange, resulting in some units where the flange is not correctly installed. Continued use in this condition may cause vibration …
Inadequate heat protection measures on the exhaust pipe allow heat generated by the exhaust to transfer to the fuel tank, fuel vapor recovery canister piping, parking brake attachment components, and other parts, …
Incorrect wheel bearing spare parts were shipped, resulting in some vehicles being equipped with non-genuine parts. Continued use in this condition causes bearing separator wear and iron particle generation, leading to premature …
Rear wheel brake calipers have improper manufacturing, resulting in oversized cylinder bore diameters in the parking brake piston bore. This compromises internal seal integrity, allowing brake fluid leakage, illuminating warning lights, and …
In the transmission control module, the control program is inappropriate, which may cause the solenoid current value that actuates the clutch plate to be detected as abnormal. As a result, the warning …
The main harness electrical wiring protective sheathing is secured improperly. Repeated handlebar operation can cause electrical wiring to become exposed from the protective sheathing. Continued use may result in exposed wiring contacting …
The airbag control unit may contain foreign matter inside due to improper cleaning during manufacturing. As a result, foreign matter may contact elements on the electronic circuit board of the unit due …
Large-size transit buses equipped with automatic transmissions may have insufficient bolt preload on torque converter cover attachment bolts of the torque converter backing plate due to improper bolt tightening method and improper …
②In left-hand drive vehicles, the driver's floor carpet may be installed with deflection due to improper attachment. When the accelerator pedal is fully depressed, the accelerator arm may contact the floor carpet, …
Fuel piping has inadequate cleaning during manufacturing, leaving oxidation film residue on the pipe surface, which causes poor adhesion of the brazing solder used as adhesive. Continued use in this condition may …
In the brake pedal of the braking system, the retaining circlip for the brake pedal shaft may not be installed during brake pedal assembly. Continued use in this condition may cause the …
The high-voltage battery mounting location has inadequate water drainage design. If water enters this location for any reason, it cannot be drained. Water may then ingress through the battery fan section, causing …
The inflators of the side airbags in the driver and front passenger seats were manufactured improperly. During airbag deployment, the inflator container may rupture and scatter component parts, risking injury to occupants.
The inflators of the driver and passenger seat side airbags are subject to improper manufacturing, which may cause the inflator housing to rupture during airbag deployment, scattering component fragments and potentially injuring …
1. In the power transmission system, improper assembly of the pulley for belt drive has resulted in insufficient fastening torque on the pulley lock nut. As a result, the nut may loosen …
1. In the power transmission system, improper assembly of the belt-drive pulley may result in insufficient fastening torque of the pulley retaining nut. This can cause the nut to loosen during operation, …
1. In the power transmission system, improper assembly method of the belt-drive pulley results in insufficient fastening torque on the pulley retaining nut. Consequently, the nut may loosen during operation, causing abnormal …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.