Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 73 of 175
In the steering system, the parallel pin for positioning the steering cylinder is of inappropriate length. When the steering cylinder is assembled to the front axle case, the parallel pin contacts the …
In four-wheel drive small buses, improper placement of the fuel filter case allows flying debris and stones to impact the case during operation, causing cracks to develop. Continued use in this condition …
In the brake booster, improper manufacturing of the diaphragm has resulted in some units where the diaphragm thickness exceeds specifications. Cracks may develop in the diaphragm's curved section, and if operation continues …
On the roof side garnish, the molding of the positioning protrusion for the curtain shield airbag label attachment location is improper, resulting in sharp edges on some protrusions. Contact with these protrusions …
In the blower fan electrical circuit, the connector and harness terminal materials are inadequate. Vibration causes metal wear at the terminals, increasing electrical resistance. Prolonged operation at fan speed 4 (high) or …
The radiator fan motor brush material is inappropriate, causing the brush to absorb moisture and swell, resulting in poor contact and potential motor stoppage. This may lead to air conditioning malfunction and …
The fuel delivery pipe in the engine's fuel system has an improperly tightened fuel pressure sensor due to inadequate torque specifications. This results in reduced axial force at the fastening point, causing …
In the audio amplifier, speaker drive elements located near cooling air vents lack a protective circuit. If foreign objects cause these elements to short circuit, excessive current flows and damages the elements. …
The driver-side SRS airbag inflator contains an improperly designed ignition charge for the gas generator. As a result, the gas generator may not combust during a collision, and the airbag may not …
DC-DC converter inspection procedures were inadequate, causing excessive voltage to be applied to some units, which damaged internal circuit boards. Continued use of affected converters may result in internal short circuits, leading …
In the front wheel suspension, the damper and knuckle fastening work was performed improperly, resulting in insufficient nut torque in some vehicles. If used in this condition, the nut may loosen and …
In the front wheel brake system, improper brake hose routing causes the bend radius to become excessively small when the steering wheel is turned fully. Repeated flexing can cause internal cracking of …
The waterproof diaphragm in the power steering control unit may be improperly installed, resulting in inadequate waterproofing. Continued use in this condition allows moisture to enter the unit, damaging the electronic circuit …
The power connector to the fuse box, located in the fuse box positioned deep within the passenger-side glove compartment, may have insufficient insertion. Continued use in this condition can result in poor …
The electric power steering (EPS) control computer has an inappropriate EPS assist shutoff voltage setting. When the battery is degraded, battery voltage may drop below the EPS assist shutoff voltage during large …
In idle stop systems using capacitor power, the boost-buck charging/discharging converter lacks sufficient overcurrent protection for its internal elements that regulate capacitor charge/discharge voltage. Overcurrent generated during restart from idle stop and …
The SRS (Supplemental Restraint System) control unit, which regulates airbags and occupant protection devices, may have defective integrated circuit manufacturing. This can cause semiconductor corrosion within the circuit. Continued use may result …
In foot-operated parking brakes, improper bracket manufacturing results in insufficient clearance between the bracket and pole in some units. This causes increased resistance during parking brake operation, and in worst cases, may …
Some brake pedal assemblies lack a retaining circlip on the brake pedal shaft during assembly. Continued use in this condition may allow the brake pedal shaft to disengage from the brake pedal …
In the rear brake master cylinder, the piston cup seal material is inappropriate, resulting in insufficient strength of the cup seal in some units. Continued use in this condition may cause the …
The design of the straw discharge device in the threshing mechanism of the combine harvester is inadequate, allowing straw to wrap around the drive pulley. Continued operation in this condition may cause …
In the exhaust pipe of combine harvesters, the exhaust pipe connection design is inadequate. When harvesting and threshing in wet paddies, mud can accumulate at the exhaust pipe connection, preventing outside air …
In the rectifier, improper moisture control during power module (electronic composite element) manufacturing can cause adhesive failure between the finned case and power module after prolonged idling followed by sustained high-engine-speed operation. …
In large and medium-sized buses, the battery-side wiring of the starter motor has improper fastening. Continued operation in this condition may cause the wiring to loosen due to vehicle vibration, leading to …
The airbag control unit substrate coating is defective, causing cracks in the coating. Continued use in this condition allows moisture from condensation and other sources to enter the substrate through coating cracks, …
In the VDC (Vehicle Dynamics Control) unit, the electric parking brake control program is inappropriate. When the electric parking brake is engaged during vehicle parking and the ignition switch is operated from …
Direct injection turbo engine intake ducts were manufactured with non-standard materials due to inadequate manufacturing controls. This causes degradation of oil resistance and heat resistance during use, leading to cracking of the …
Due to improper fuel tray shape, water entering during washing may accumulate in the fuel tray and infiltrate the fuel tank. When the fuel pump draws in this water, engine malfunction may …
Improper routing of the fuel tank drain tube and fuel tray design can allow the drain tube to become obstructed by debris. This permits water ingress into the fuel tank during rain …
The air conditioning compressor may have an improper refrigerant oil charge level, resulting in insufficient lubrication inside the compressor during air conditioning use. Continued operation under this condition can cause internal compressor …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.