Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 78 of 175
The inflator (inflation device) for the front passenger airbag may suffer container rupture during deployment. Although the cause has not been determined, all vehicles will undergo preventive replacement of the inflator as …
The electronic stability control (ESC) system controller has an inadequate control program. During ESC operation, electromagnetic interference from the brake control drive motor may cause the yaw rate sensor signal built into …
The hydraulic clutch master cylinder has inadequate internal cleaning during machining, leaving manufacturing chemicals not fully removed. These chemicals react with brake fluid inside the master cylinder, causing gas bubbles to form …
In rotary snow removal vehicles, the fuel filter mounting bracket design is inadequate, resulting in insufficient vibration isolation against engine vibration. Engine vibration may cause cracks in the fuel filter, leading to …
The engine ECU control program has an improperly set learning limit value for idle air volume correction. When carbon accumulates on the throttle valve, idle air volume may become insufficient, potentially causing …
The fuel pressure sensor attached to the fuel line may have insufficient tightening due to improper manufacturing. This may cause fuel leakage from the fuel pressure sensor mounting point.
Improper assembly of inner arch liners installed within the front wheel fenders on the left and right sides; in some cases, the inner arch liner contacts the brake hose. Continued use in …
On trailers subject to mid-stage brake regulations with single-axle or lift-axle configurations, related components such as air control valves may be used beyond their service life limits, causing air leakage and reduced …
In the parking brake of wheel loaders, improper manufacturing instructions have resulted in incorrect positioning of the washer at the coupling between the parking brake actuation lever and push rod. Consequently, vibration …
In the front axle suspension system of large tractors, (2) the fastening torque of the anchorage and flange screws securing the air bellows may be inappropriate. Consequently, flange screw loosening may occur …
The main harness for engine control and other systems has improper routing, causing contact with the oil tank in some vehicles. Vibration during driving causes the harness insulation to wear, and continued …
In the engine compartment, certain rubber seals have been manufactured with improper specifications, resulting in weak retention force to the bulkhead. When the engine hood is opened, the seal may adhere to …
The snap ring geometry that joins the drive shaft and wheel-side joint inner race is improper, which may cause the snap ring to detach due to vibration during driving. As a result, …
In LPG-equipped vehicles, the LPG engine control harness has insufficient fuse and wiring current capacity ratings. When operating in LPG mode under high load and high RPM conditions, current exceeding the fuse …
In the lithium-ion battery of hybrid vehicles, the inspection method for the harness connected to the battery controller was inadequate, resulting in some connector terminals having excessive gaps. Continued use of such …
Certain airbag control units have insufficient resistance to electrical noise. Consequently, noise generated from vehicle electrical components may damage the IC chip within the unit during use, and in the worst case, …
Certain airbag control units have insufficient resistance to electrical noise. Due to noise generated by vehicle electrical components during use, the IC chip within the unit may be damaged, and in the …
The driver seat airbag inflator has been found to exhibit abnormal internal pressure output in the inflator canister that could lead to unintended deployment. This was discovered during the component manufacturer's investigation …
The engine control computer has an inadequate control program for the exhaust gas recirculation (EGR) valve. Repeated accelerator pedal operation causes the EGR valve opening to deviate from control commands, potentially preventing …
The engine control computer has an inadequate control program for the exhaust gas recirculation (EGR) valve. Repeated accelerator pedal operation causes the EGR valve opening to deviate from control commands, potentially failing …
In the inflator (inflation device) of the front passenger airbag, improper molding of the gas generant or inadequate moisture-prevention measures after molding may result in gas generant with insufficient density being incorporated. …
Due to improper engine manufacturing, some fuel pump mounting nuts are insufficiently tightened. If operation continues in this condition, the nut may loosen, causing the fuel pump to vibrate, and in the …
Some fuel pumps have inadequate fuel flow rate management during manufacturing, resulting in low fuel flow. Additionally, the engine control unit (Engine ECU) control program is inappropriate, which may cause excessive fuel …
In the EGR cooler and EGR valve housing of the exhaust gas recirculation (EGR) system, certain materials are inadequate and corrode due to exhaust gas condensation water. Corrosion debris may jam the …
The driver-side airbag module has been manufactured improperly, which may result in insufficient airbag deployment during a collision and compromise occupant protection performance.
In turbocharged vehicles, improper assembly of the parking brake cable results in interference between the right-side parking brake cable and fuel tank in some units. Continued use may cause the fuel tank …
In the steering system, improper manufacturing processes of the steering arm may cause the lock nut on the tie rod to loosen. Continued use in this condition can result in slack in …
In the body structural components of large trucks, the design of the equipment installation is inadequate, resulting in insufficient clearance between the brackets connecting the longitudinal and transverse sills and the electrical …
Due to an inappropriate control program in the electric parking brake, errors may occur in the cable winding value of the parking brake in the electric parking unit during parking brake engagement …
The inflator in the driver-side airbag may rupture due to internal pressure during airbag deployment, causing component fragments to scatter and potentially injuring occupants.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.