Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 87 of 175
In heavy-duty trucks equipped with 12-speed mechanical automatic transmissions, oil mist contained in compressed air supplied from the air compressor undergoes oxidative degradation, generating black sticky deposits. These deposits can cause seizure …
In the electronically controlled rear suspension, improper manufacturing of the damper spring causes the spring to not compress vertically when excessive force is applied to the suspension, risking suspension damage. This results …
The wheel cylinders for the rear wheel primary brake have insufficient corrosion resistance on the piston. During use, moisture from the atmosphere can enter the cylinder, causing rust to form on the …
Some front brake hoses are installed pinched between the fuel tank and frame. Continued use in this condition may cause front brake drag during operation, and in the worst case, the front …
In the front suspension, some lower arm mounting bolts have insufficient strength. If vehicles continue to be used in this condition, the bolts may fracture, causing abnormal noise and potentially affecting steering …
The fuel pump quick coupler removal/installation instructions are inadequate, which can cause cracks to develop in the fuel pump mount dome. As thermal expansion and contraction of the fuel pump progresses the …
Due to improper ECU programming, when the ECU-estimated clutch friction characteristics deviate from actual clutch friction characteristics during EV mode driving and the engine is started by motor drive, excessive motor driving …
The swing-lock mechanism that maintains the vehicle's upright position when the parking brake is engaged has improper machining of the support bracket, which can result in shallow engagement between the swing-lock pole …
In the fuel piping of wheel loaders, due to inappropriate piping configuration and material, fuel piping cracks may develop under the pulsating load of the fuel pump. If operation continues in this …
Certain airbag control units have insufficient electrical noise immunity. Noise generated during power seat operation can damage IC chips within the unit during use, potentially causing airbag deployment while driving.
Due to improper programming in the automatic transmission control computer, the gear position may not be accurately detected relative to the clutch position during driving. This may result in the gear position …
In the automatic transmission, the shift cable is not properly installed, and may detach during use. If detachment occurs, shift operations will not function correctly, potentially causing unintended vehicle movement or, depending …
The passenger airbag inflator may contain a gas generant with insufficient density due to improper molding of the gas generant or inadequate moisture prevention measures after molding. During airbag deployment, abnormal pressure …
In the instructor seat auxiliary brake of training vehicles, the snap pin structure designed to prevent cotter pin loss on the brake pedal is inadequate. Depending on usage conditions, the snap pin …
In the parking brake equipped on asphalt finishers, the bolts and nuts securing the parking brake caliper and the bolts of the caliper mounting bracket are improperly tightened, causing loosening in some …
In large intercity buses equipped with automatic transmissions, the electrical circuit controlling the middle door is defective. Under the following conditions, the middle door may open while driving: (a) After the driver …
The adjustment units of the variable valve timing systems on both the intake and exhaust sides have bolts with insufficient strength, which may fracture. This can cause the system to malfunction, illuminate …
The passenger-side airbag inflator may contain gas generant with insufficient density due to improper molding of the gas generant or inadequate moisture-prevention measures after molding. This can cause abnormal pressure rise within …
The passenger-side airbag inflator contains gas-generating agents with insufficient density due to improper molding process or inadequate moisture-prevention measures post-molding. During airbag deployment, abnormal pressure rise within the inflator can cause the …
Passenger-side airbag inflators contain gas generant with insufficient density due to improper molding of the gas generant or inadequate moisture prevention measures after molding. During airbag deployment, abnormally elevated pressure within the …
The fuel pipe uses inadequate material with insufficient durability, causing cracks during use that may result in fuel leakage and potential fire.
Passenger airbag inflators contain gas generant with insufficient density due to improper molding process or inadequate moisture prevention measures post-molding. During airbag deployment, abnormal pressure rise within the inflator may cause the …
Passenger-side airbag inflators contain gas generant with insufficient density due to improper molding process or inadequate moisture-prevention measures post-molding. During airbag deployment, this can cause abnormally elevated internal pressure in the inflator, …
Passenger-side airbag inflators may contain gas-generant charges with insufficient density due to improper molding of the gas-generant or inadequate moisture-prevention measures after molding. During airbag deployment, this can cause abnormal pressure rise …
Improper selection of the mounting bolt for the suspension lock cylinder fixing pin has caused the bolt to loosen and potentially detach. If operation continues in this condition, the suspension lock cylinder …
Due to an inadequate control program in the engine ECU, the fuel pump pressure regulator may be incorrectly determined to be stuck. In such cases, the engine warning light illuminates, output is …
In the rear suspension, the nut securing the toe control link rod to the rear subframe has insufficient strength. Under severe use conditions such as circuit driving, the nut may fail and …
The bolt securing the front-rear link arm to the knuckle on the right rear suspension was tightened with excessive torque. Under driving loads, this bolt may fracture, potentially causing wheel misalignment and …
The automatic transmission control computer program is inadequate, which may prevent accurate detection of gear position and clutch position during driving. As a result, the gear position may become fixed, or in …
Certain genuine accessory brake levers have improper plating. This can cause the brake lever to obstruct master cylinder piston operation, resulting in front brake drag. In worst-case scenarios, front wheel lock may …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.