Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 89 of 175
In turbocharged vehicles, the engine ECU program has inadequate control of fuel injection volume, air volume, and spark plug ignition timing, which may cause engine speed to drop in the low-speed range, …
The starter relay in the starting device has improper energization settings, causing silver components to accumulate at the contact points. Continued use in this state may result in silver components separating from …
The mounting bracket securing the steering column to the vehicle interior (under the instrument panel) has insufficient strength. Repeated hard full-lock steering operations may cause cracks to develop. Continued use allows crack …
The windshield wiper motor mounting area has an improperly shaped drainage port. If operated without removing debris such as fallen leaves, the drainage port may become clogged. Continued operation can cause overflow …
The slide mechanism for front-to-back adjustment of the driver's seat has insufficient spring strength for the locking function. Frequent adjustment may cause the spring to fracture, resulting in the seat not being …
The electrical wiring (spiral cable) attached to the steering wheel has improperly shaped and positioned guide features. This causes point contact between the airbag wiring section and the guide edge, resulting in …
The ignition switch rotational resistance may fall below design specification. When key chains or similar items are attached to the ignition key, driving vibrations may cause the key to move to a …
In push-button type parking brake switches, improper machining during the manufacturing process results in insufficient clearance in the internal sliding components. Consequently, at low ambient temperatures, contraction of the switch body due …
In the automatic clutch mechanical transmission control unit, CNG engine control unit, or trailer information control unit installed below the instrument panel of trucks, if maintenance (replacement) of the coolant (antifreeze) circulating …
Due to incorrect initialization of the body control module, when braking is applied, the amber rear turn signal may illuminate in addition to the brake light.
The ignition switch has lower rotational resistance than designed specifications. When a key ring or other attachments are installed on the ignition key, driving vibrations may cause the ignition key to move …
Non-compliant lighting is installed as the brake light.
The brake light mounting position is improper.
On large trucks equipped with spring brake chambers on the front axle, the ABS control valve bracket has an improper shape, resulting in insufficient clearance between the front right wheel spring brake …
The parking stand mechanism (used to support the vehicle body while the rear wheel remains in contact with the ground) has an inadequate design. The rear brake lever must be pulled with …
In large sightseeing hybrid buses, due to improper programming of the vehicle control ECU, after ABS actuation, the ECU may rarely remain in an active state recognition even when ABS is no …
In trucks, the ABS, mechanical automatic transmission, AT, or four-wheel drive control units mounted below the instrument panel may experience corrosion in the cooling circuit if coolant (antifreeze) maintenance in the heater …
In the front wheel brake, due to improper positioning of the inner wire casting at the cable end, repeated operation of the parking lever during parking on slopes and similar conditions may …
Vehicles equipped with an optional dealer-supplied cold-climate front brake cable may experience cable end breakage. The inner wire casting position at the cable end is improper, causing the cable end to fracture …
The connector design in the rear combination light bulb carrier is inadequate, causing contact failure due to vehicle vibration. When the light is illuminated in this state, the connector may overheat. Repeated …
The alternator harness routing in blood collection vehicles is improper. Vibration from driving may cause the harness to contact the exhaust gas recirculation (EGR) cooler. Continued use in this condition may result …
In the Keyless Operation System Control Unit (KOS ECU), a manufacturing defect in the internal reset IC may cause the reset IC to malfunction in extremely low temperatures, resulting in microcontroller shutdown …
Certain hybrid large-capacity transit buses have inverters with insufficient durability and reliability in their current conversion devices. Inverter failure may prevent the drive motor and auxiliary motor from operating, causing the hybrid …
The brake plate, a component of the braking system, has an improperly designed groove intended to prevent interference between the brake shoe and brake plate. Concentrated tensile and compressive forces during braking …
The brake plate, a component of the braking system, has an improperly designed groove intended to prevent interference between the brake shoe and brake plate. Tensile and compressive forces concentrate in the …
In the engine, an incorrect corrosion preventative was applied to the sealing bolts that restrict rocker arm shaft rotation. Engine heat causes the fastening torque to decrease, resulting in bolt loosening and …
In vehicles equipped with diesel turbo engines, some intercooler hoses connected to the throttle chamber have insufficient clamp fastening force. Continued use may cause the hose to become disconnected due to engine …
In the controller for the forward/reverse hydraulic clutch of the power transmission device, due to an inappropriate travel control program, unintended sharp turning may occur when left steering is immediately performed after …
Due to improper assembly procedures during wheel loader manufacturing, some rear axle trunnion fastening plate bolts are missing washers. Continued use in this condition may cause bolt torque to loosen, resulting in …
In the 7-speed DCT automatic transmission of hybrid vehicles, the sleeve does not move smoothly on the hub of the 1st gear inside the transmission. As a result, the 1st gear may …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.