Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10559 recalls on record · page 219 of 352
The gap between the seat belt mount and seat belt anchor fixing pin on the driver and passenger seats is excessive. When detaching the seat belt with the seat in the fully …
The electrical circuit displaying starter switch operation status in training vehicles is defective. When the engine operation confirmation lamp display is switched from engine-off state to starter switch operation state, the side …
In the power transmission system of agricultural tractors, an incorrect part was installed as the fixed nut of the axle clutch, which may cause the nut to loosen. This may result in …
The rear brake light switch has inadequate water-resistant construction. The switch reaches high temperatures from heat exposure near the catalytic converter, and when cooled by water ingress, moisture is drawn in through …
In large buses, improper routing of the underbody harness results in contact between the harness and piping mounting brackets in some vehicles. Continued operation in this condition may cause the harness covering …
In superchargers for compressed natural gas vehicles, some turbocharger blades have insufficient strength and may fracture. This can result in white smoke emission and power loss, potentially rendering the vehicle inoperable.
The shape of the radiator protection guide installed on the radiator shroud panel during assembly is inappropriate, causing interference with the automatic transmission oil hose. Consequently, during prolonged operation on unpaved roads …
The ball serving as the fulcrum for the rocker cam that controls hydraulic fluid flow in the steering system hydraulic pump has insufficient wear resistance. Consequently, the ball may wear, and continued …
The connecting coupling on the front axle drive shaft of the power transmission system has insufficient strength, which may cause cracks to develop in the coupling's weld. Continued use in this condition …
In small buses, improper welding of the air spring cover on the left rear wheel may cause the welded joint to separate due to vibration during operation, risking loss of the cover.
In small buses, the welding of the air spring cover on the left rear wheel is improper, and due to vibration during operation, the welding may separate and the cover may detach.
The heating elements (seat heater elements) in the driver and passenger seat heaters have insufficient durability. During prolonged use, cracks may develop in the heating film. This causes changes in electrical resistance …
Some propeller shaft spline yokes have inadequate strength due to improper heat treatment. Continued use may cause cracking at the affected location, and in the worst case, propeller shaft failure resulting in …
In vehicles equipped with the optional SRS side and curtain airbags, the bracket securing the curtain airbag to the vehicle body may not be properly fixed. As a result, the airbag may …
Incorrect connection of engine electrical wiring may prevent proper fuel injection timing control, potentially causing exhaust gas emissions during operation to exceed regulatory limits set by road vehicle safety standards.
Incorrect connection of engine electrical wiring may cause the alternator to cease generating power when a bulb failure occurs in the battery warning light. Continued operation in this condition may result in …
Some propeller shafts have inadequate strength due to improper heat treatment of the spline yoke. Continued use may cause cracks to develop at the affected location, and in the worst case, propeller …
In compressed natural gas (CNG) vehicles, the transmission control unit program for the mechanical automatic transmission is improper, which may prevent gear shifting and cause a mismatch between the shift lever position, …
In compressed natural gas (CNG) vehicles, improper fuel filling procedures at the assembly factory can cause cracks to develop inside the fuel tank safety valve material. Continued use in this condition may …
The clip securing the hydraulic line to the clutch master cylinder lacks sufficient strength and may be damaged by hydraulic pressure from clutch operation. This can cause the line to disconnect and …
In the rear axle differential (rear differential), incorrect bolts have been installed in some units to secure the rear differential cover. Continued use may result in bolt loosening, oil leakage, and in …
The valve material and dimensions inside the ASR (Anti-Spin Regulator) valve, which is installed to prevent drive wheel slippage, are inappropriate. Due to aging from air pressure acting on the valve's rear …
In the acceleration control device, machining oil from the molding process adheres to a disk within the mechanism that regulates pedal operating force. During use, friction between the disk and plate gradually …
In the steering system, the assembly process for the screw that fixes the power steering hydraulic pipe to the steering gearbox was improper, resulting in some screws not being installed correctly. This …
The engine is not equipped with a blow-by gas reduction device and does not comply with road transport vehicle safety standards.
Certain rear-wheel shock absorbers have insufficient fastening torque on the axle-side mounting bolts. Vibration during driving may cause these bolts to loosen, generating abnormal noise. Continued use could result in separation of …
The manufacturing process for the automatic transmission (A/T) oil cooler piping and oil cooler hose is inadequate, resulting in some units with improper piping machining and others with insufficient hose cleaning treatment. …
The fuel return hose from the engine to the fuel tank was assembled incorrectly. During use, this hose may become damaged, causing fuel leakage, which in the worst case could lead to …
Some vehicles have insufficient tightening of the fastening bolts on the universal joint connecting the steering shaft and gearbox. When full-lock steering maneuvers are performed, these bolts may loosen, causing abnormal noise …
On tank semitrailers, torsional stress applied to the ends of leaf springs can cause cracks to develop near the spring end joint. Continued use without correction may result in spring fracture in …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.