The accelerator return spring provided on the accelerator pedal may have insufficient strength due to improper manufacturing process. If use continues in this condition, the spring may fracture, and in the worst …
Komatsu FD100 2008–2010
Komatsu FD115 2008–2010
Komatsu FD120 2008–2010
Komatsu FD135 2008–2010
Komatsu FD150E 2008–2010
+10 more
The accelerator return spring provided on the accelerator pedal may have insufficient strength due to improper manufacturing process. Continued use in this condition may cause the spring to fracture, potentially resulting in …
Komatsu GD755-5 2006–2010
Komatsu GH320-5 2006–2010
Komatsu WA200-6 2006–2010
Komatsu WA270-6 2006–2010
Komatsu WA320-6 2006–2010
+5 more
Due to inadequate control programming in the Variable Gear Ratio Steering System (VGRS), rapid steering wheel return operations following normal stationary turning can cause the steering wheel neutral position to temporarily deviate …
Lexus LS 460 2009–2010
Lexus LS 460L 2009–2010
Lexus LS 600h 2009–2010
Lexus LS 600h L 2009–2010
The upper arm of the front wheel suspension has improper position control during welding of two sheet metal plates, resulting in misalignment of the ball joint mounting hole position on some units. …
Mitsubishi Triton 2006–2009
The rubber hose connecting the primary and secondary chambers of a dual-chamber fuel tank, and the filter unit on the secondary chamber side, were assembled improperly. This can cause the rubber hose …
Honda Odyssey 2009
In welfare vehicles equipped with hydraulic wheelchair lifts, the floor-level position detection switch lacks sufficient dust sealing. Foreign matter such as sand and dust can accumulate around the switch. Additionally, the return …
Mitsubishi Town Box 2004
Mitsubishi Minicab 2004
Nissan Clipper 2004
The solder temperature of the operation switches on both sides of the steering wheel is inappropriate, which may cause wiring fractures on the switch circuit board. As a result, the operation switches …
BMW BMW F800R 2008–2009
BMW BMW K1300GT 2008–2009
BMW BMW K1300R 2008–2009
BMW BMW K1300S 2008–2009
On vehicles equipped with high-capacity alternators, the installed fuse has insufficient capacity, which may cause the fuse to blow and prevent battery charging. Continued operation in this condition may result in engine …
Komatsu GD655-3 2006–2007
In the fuel system of agricultural tractors, insufficient fuel tank strength can cause tank distortion due to assembly variation or vibration during operation, potentially resulting in cracks and fuel leakage. Additionally, some …
ヰセキ CT55H 2001–2007
ヰセキ CT65H 2001–2007
ヰセキ CT75H 2001–2007
ヰセキ TJ55 2001–2007
ヰセキ TJ55AT 2001–2007
+5 more
Agricultural tractors equipped with noise suppression devices may have exhaust pipes with insufficient strength, interference between the exhaust pipe and hood, or insufficient clamp fastening torque. Continued use in this condition may …
ヰセキ CT55H 2001–2009
ヰセキ TJ55 2001–2009
ヰセキ TJ55AT 2001–2009
ヰセキ TJ65 2001–2009
ヰセキ TJ75 2001–2009
In the running gear of agricultural tractors, the idler wheel bearing portion of the endless rubber crawler has insufficient strength. When snow or mud adheres to the idler wheel and crawler tension …
ヰセキ CT55H 2007–2010
ヰセキ CT65H 2007–2010
ヰセキ CT75H 2007–2010
ヰセキ CT85H 2007–2010
ヰセキ TJ55AT 2007–2010
+3 more
During installation of the instructor horn switch in training vehicles, a connector with non-conforming specifications was assembled. This may cause connector terminal contact failure due to vibration during operation, resulting in the …
Mazda Axela 2009–2010
In the battery harness connected to the alternator, the terminal connection portion of the harness is bent during assembly. If operation continues in this state, vibration may cause the terminal connection to …
Komatsu FD20 2009–2010
Komatsu FD25 2009–2010
Komatsu FD30 2009–2010
Komatsu FD30H 2009–2010
Komatsu FD35A 2009–2010
In LPG-specification engine forklifts, improper bending during LPG pipe manufacturing may cause wrinkling at the bend point. Continued use in this condition can result in LPG pipe damage due to engine vibration, …
Toyota Toyota Geneo 2006–2007
The write program for configuration data in the vehicle control computer is inappropriate. Upon charging plug insertion, the set value for deceleration force during plugging braking (deceleration by switching between forward/reverse without …
ニチユ Transer 2010
In vehicles equipped with arm-type tailgate lifters, spacers installed to lower the spare tire mounting height are attached using an improper installation method. Repeated driving vibrations can cause cracks to develop in …
Isuzu Elf 2007–2009
Nissan Atlas 2007–2009
Certain tires equipped as standard on vehicles have improper sidewall structure, making them susceptible to fatigue accumulation in the sidewall. During use, cracks may develop in the sidewall, and continued use could …
Fiat 147 2008
Improper welding of the exhaust pipe flange may cause cracks to develop at the weld due to engine vibration. In the worst case, the flange may fracture, resulting in increased exhaust noise.
タダノ GR-250N-2 2008–2010
The fastening bolts at the fixed portion (support joint cover) of the steering joint connecting the steering wheel and power steering unit are insufficiently tightened in some units. Continued operation may cause …
Kubota KB17X 2010
Kubota KB17XF 2010
Kubota KB19X 2010
Kubota KB21X 2010
Kubota KB21XF 2010
+2 more
In the recall notification (Notification No. 2101) filed on April 18, 2008, improper work instructions for recall service resulted in some units where protective material was not added to the traveling hydraulic …
コべルコ SK125W 2006–2008
The surface hardness of the vehicle speed sensor rotor inside the transmission is inadequate, causing wear on the rotor end face. This can result in loosening of the flange coupling fastening bolts …
Hino Hino Super Dolphin 2000–2007
Hino Hino Profia 2000–2007
In large buses, the stay damper mounting bracket for swing-type trunk lids has insufficient strength, which may cause cracks in the bracket during trunk lid opening and closing operations. If use continues …
Mitsubishi Fuso Aero Ace 2007–2010
Mitsubishi Fuso Aero Queen 2007–2010
Nissan - 2007–2010
Due to equipment failure during the tire and wheel assembly process, some tires have scratches on their sidewalls. Continued use in this condition may result in progressive scratch propagation, risking pressure loss …
Mitsubishi Galant 2009–2010
On the rear-rear axle of large cargo vehicles (rear-front 1-axle drive, 3-axle configuration), some vehicles have insufficient strength margin for their operating environment, which may cause cracks to develop in the axle. …
Nissan - 1995–1999
Incorrect fastening nuts were installed on the linkage connecting the front suspension stabilizer and strut. Due to vibration during driving, these nuts may loosen, causing abnormal noise, and in the worst case, …
Peugeot 207 2009
Peugeot 207 Style 2009
In the manufacturing process of the rear spoiler, the welding process joining the spoiler upper section to the spoiler body is inadequate, resulting in insufficient weld strength in some units. This causes …
Citroen C5 2008–2009
Inadequate adhesion between the metal frame and resin panel in the roof section may cause the bond to separate due to vibration during driving. Continued use may result in panel detachment, and …
Chevrolet Corvette 2004–2008
Chevrolet Corvette Z06 2004–2008
The gap between the seat belt mount and seat belt anchor fixing pin on the driver and passenger seats is excessive. When detaching the seat belt with the seat in the fully …
Porsche Panamera 4S 2009–2010
Porsche Panamera S 2009–2010
Porsche Panamera Turbo 2009–2010
The electrical circuit displaying starter switch operation status in training vehicles is defective. When the engine operation confirmation lamp display is switched from engine-off state to starter switch operation state, the side …
Honda CB400 SUPER FOUR 2008–2010
In the power transmission system of agricultural tractors, an incorrect part was installed as the fixed nut of the axle clutch, which may cause the nut to loosen. This may result in …
ヰセキ TPC153 2009–2010
ヰセキ TPC183 2009–2010
ヰセキ TPC213 2009–2010