Komatsu: Window Glass
JapanThe front windshield has a light-blocking panel affixed, which does not comply with road transport vehicle safety standards.
Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10559 recalls on record · page 225 of 352
The front windshield has a light-blocking panel affixed, which does not comply with road transport vehicle safety standards.
The automatic transmission clutch temperature sensor may have insufficient crimping of the wiring harness at manufacturing, causing erroneous signals to be sent to the electronic control unit. This can result in false …
The welding at the guide attachment point on the front wheel brake hose retaining bracket may be improper. This can cause cracks to develop at the attachment point due to vibration during …
The pinion shaft retaining nut in the steering gear of the steering system has improper machining, which may cause the nut's clamp force to decrease during use. Consequently, the nut may gradually …
The reduction gear manufacturing process of the continuously variable transmission (CVT) was inappropriate, resulting in cutting burrs remaining in the oil passages of the affected gears. Continued use may cause these burrs …
The fuel pump unit mounting area on the fuel tank has improper drilling, resulting in sharp protrusions on the mounting surface. Continued use may cause cracks to develop in the gasket at …
The pinion shaft retaining nut in the steering gear of the steering system has improper machining, which may cause the nut's clamping force to decrease during use. Consequently, the nut may gradually …
Insufficient evaluation of the welded joint between the main frame and reinforcement pipe results in inadequate frame strength. Excessive loads such as curb impacts may cause cracks to develop in the frame. …
The damper coupling installed at the connection between the engine and hydraulic pump has inadequate fastener tightening on some units. Continued operation in this condition may cause the coupling to disengage, rendering …
In the traveling hydraulic piping, improper bending of the pipe may cause cracking in the piping due to hydraulic pressure during operation. Continued use in this condition risks hydraulic fluid leakage, and …
The hydraulic piping for propulsion has insufficient strength in the pipe fittings and inadequate fastening torque in the pipe brackets. Vehicle vibration and other factors may cause cracks in the pipe fittings. …
Front or side window glass does not comply with road transport vehicle safety standards due to affixed nameplates (warning plates, etc.).
The fixing method for the resin component that secures the window frame of the driver-side opening/closing glass to the vehicle body is improper, resulting in some window frames not being securely fixed. …
In the powertrain system, improper wiring fixation of the forward/reverse selector solenoid valve causes the wiring to resonate and break due to transmission vibration. This prevents forward/reverse switching of the solenoid valve, …
The fastening torque specification for the mounting bolts securing the front axle to the chassis is inappropriate, which may cause the bolts to loosen due to repeated loads during snow removal and …
Due to inappropriate bearing material and clearance between the fuel injection pump speed control lever shaft and its bearing, repeated accelerator operation causes the shaft and bearing to seize. This results in …
In the steering system, some power steering pump mounting brackets have machining defects in the mounting holes. If operation continues in this condition, the power steering pump mounting bolts may loosen, and …
The automatic transmission clutch temperature sensor has insufficient crimping of wiring at manufacture, causing erroneous signals to the electronic control unit. This results in misdiagnosis of abnormal transmission fluid temperature. As a …
The rear fender flap geometry is improper. Due to vehicle assembly tolerances, tires may protrude beyond the fender flap, potentially failing to comply with safety standards under the Road Transport Vehicle Act.
Due to improper programming in the main control module, if the engine is restarted immediately after shutdown, power may not be supplied to the fuel pump, preventing engine start.
Certain dual-axle 16-wheel trailers have defective welds at the shaft trunnion-spindle joint. Continued use may cause cracks to develop in the axle. In the worst case, axle fracture could occur, resulting in …
In the intermediate shaft of the steering apparatus, the pinion shaft insertion is insufficient in some units, resulting in inadequate fastening. Consequently, the pinion shaft may gradually come loose, and in the …
The retaining screw that secures the check ball inside the power steering valve of the steering apparatus has insufficient clamping force, causing the screw to loosen and the check ball to fall …
On the front axle of forklifts, the seal structure of the parking brake mounting section is inadequate, which may cause lubricating oil to leak. Leaked lubricating oil may enter the parking brake, …
The brake accumulator (pressure reservoir) is secured using an improper fixing method. Vibration and similar conditions may cause cracks to develop in the brake piping connected to the accumulator. As a result, …
In electro-hydraulic power steering systems, improper manufacturing processes in high-pressure piping have caused internal rust formation in some units. This rust damages the bearing portions of the pump gear, increasing sliding resistance. …
The fuse for the engine ECU is shared with the fuse for the brake booster vacuum pump. If overcurrent occurs when the pump operates, the shared fuse may blow. This can cut …
The strut plate that holds the front wheel coil spring has insufficient strength. Repeated stop-and-go driving in hot, humid environments can cause cracks to develop in the plate, resulting in abnormal noise. …
In hybrid buses, the body frame shape is improper, causing interference with the fuel piping in some units. Continued use in this condition may result in fuel piping damage and fuel leakage.
Insufficient heat treatment of the transmission shaft surface for gear shifting inside the transmission can cause cracks to develop in the shaft when shift operations are repeated, potentially leading to shaft fracture. …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.