The overload relief valve attached to the traveling hydraulic motor of the power transmission system may contain foreign material from the manufacturing process. If use continues in this condition, internal seal components …
日立 ZX125W 2003–2007
日立 ZX160W 2003–2007
日立 ZX210W 2003–2007
日立 ZX300W 2003–2007
日立 ZX350W 2003–2007
The overload relief valve attached to the hydraulic motor for propulsion in the power transmission system has an internal spring with improper assembly. Continued use in this condition may cause the spring …
日立 ZX125W 2003–2007
日立 ZX160W 2003–2007
日立 ZX210W 2003–2007
日立 ZX300W 2003–2007
日立 ZX350W 2003–2007
The crankcase of the engine has casting defects in the outer wall of the oil passage, which may cause engine oil to leak during engine operation. The leaked oil may adhere to …
Kawasaki Ninja250R 2009
In the power transmission system of agricultural tractors, improper fixation of internal gears may cause the gear retaining key to fracture due to engine idle pulsation. This may result in loss of …
ヰセキ JKA21S 2005–2006
The rear suspension drag link material is inadequate, causing corrosion during use that reduces link strength. Road impact may fracture the link, destabilizing vehicle attitude and risking rollover in severe cases.
Triumph Sprint ST 1050 2005–2008
Triumph Sprint ST 1050 ABS 2005–2008
Engine oil cooler hoses used as replacement parts in the recall work (notification number 2412, dated November 12, 2009) have low hose pull-off pressure in some units. Continued use may result in …
Subaru Impreza 2002–2007
Some fuel tank caps have an improper shape that causes cracking. Repeated opening and closing operations can propagate these cracks, and continued use may result in fuel leakage.
Suzuki Vexstar 150 2007
In garbage collection vehicles, inadequate clearance between the mounting bracket securing the cargo bed to the chassis frame and the rear wheel tire creates a risk of the inner rear tire contacting …
Mitsubishi Fuso Canter 2008–2009
In the brake light (combination taillight) equipped at the rear of garbage collection vehicles, socket terminals may be installed incorrectly. This can cause poor electrical contact between the bulb and socket due …
Hino Hino Dutro 2009
Hino Hino Ranger 2009
Isuzu Forward 2009
Mitsubishi Fuso Canter 2009
Mitsubishi Fuso Fighter 2009
+1 more
The connection points between the dump mechanism and cargo bed on three-way dump trucks have insufficient structural strength. Fastening bolts may fracture, causing the dump mechanism to fall. In the worst case, …
Hino Hino Ranger 2004–2009
Isuzu Forward 2004–2009
Mitsubishi Fuso Fighter 2004–2009
Mitsubishi Fuso Fighter Mini Yoyon 2004–2009
In the driver seat airbag, due to inappropriate component changeover instructions, components of different specifications have been assembled, which may result in occupant protection performance during offset collisions not meeting safety standards.
Nissan Skyline 2009
The circuit board material inside the speedometer is inappropriate, causing repeated thermal expansion due to heat from the instrument's night illumination, which may result in an open circuit in the fuel gauge …
Nissan Cefiro 2001–2003
Nissan Serena 2001–2003
In the parking brake system, there is a gap between the guide pipe of the bracket that secures the parking brake cable to the vehicle and the protector that covers the brake …
Isuzu Fargo Filly 1997–2002
Isuzu Filly 1997–2002
Nissan Elgrand 1997–2002
Nissan Caravan Elgrand 1997–2002
Nissan Hommy Elgrand 1997–2002
Improper installation of the cover adjacent to the driver's seat has damaged the electric seat wiring in some vehicles. Continued use in this condition may cause the wiring to short circuit, resulting …
Nissan Teana 2008
In variable-nozzle turbochargers for engines, improper internal structure causes variable-nozzle return malfunction, generating high stress on turbine blades. This shortens service life and can cause turbine blade fracture. Continued operation may result …
Hino Hino Profia 2005–2006
In the brake system linkage mechanism, the mounting bolts of the brake arm pivot shaft may not be adequately tightened. Continued use in this condition can cause the bolts to loosen, resulting …
Yanmar EG220 2009
Yanmar EG222 2009
Yanmar EG224 2009
Yanmar EG224X 2009
Yanmar EG227 2009
+3 more
In the steering system of an agricultural chemical sprayer vehicle, the harness routing for the front wheel steering angle measurement potentiometer is inadequate. During use, this harness may become damaged. As a …
昭信 3S-FS1060 2005–2009
昭信 3S-FS630 2005–2009
昭信 3S-FS630H 2005–2009
昭信 3S-FSC1060 2005–2009
昭信 3S-FSC1060L 2005–2009
+7 more
The outer ring of the engine crankshaft pulley has inadequate surface treatment, resulting in insufficient adhesion to the vibration-damping rubber. Consequently, the ring and rubber may delaminate, causing abnormal noise from the …
Hyundai Grandeur LPI 2006–2007
The fuel hose connecting the fuel pump to the left chamber of the fuel tank is excessively long. When the pump is assembled to the fuel tank, the hose may kink. As …
Jaguar XF 3.0 2009
Improper selection of the spare tire carrier suspension hardware results in inadequate engagement of the spare tire carrier. In worst case scenarios, the spare tire may detach due to driving vibration or …
Hino Dutro 2005–2009
In four-wheel-drive vehicles equipped with automatic transmissions, the seal cap fitted to the internal gear end within the transfer case lacks sufficient pressure resistance, potentially causing automatic transmission fluid to leak externally …
Mitsubishi Fuso Canter 1999–2009
Mitsubishi Fuso Rosa 1999–2009
In large route buses, the braking system may experience brake fluid leakage from the power unit (air master) due to contaminants introduced into the brake fluid from inadequate cleaning of brake piping. …
Hino Hino Blue Ribbon II 2006
In bus brake systems, improper flushing of brake piping allows foreign matter mixed into brake fluid to cause leakage from the booster (air master). Continued operation in this condition can degrade rubber …
Hino Hino Blue Ribbon II 2003–2007
Hino Hino Rainbow II 2003–2007
Isuzu Erga 2003–2007
Isuzu Erga Mio 2003–2007
Isuzu Gala 2003–2007
+1 more
The tension-adjustment spring housing for the connecting cable that releases the driver's seat slide mechanism lock when the seatback is tilted forward has improper assembly in some units, resulting in insufficient structural …
Renault Twingo 2008–2009
The routing of wiring connected to the battery positive terminal is improper, and in some cases interferes with the battery box retaining bracket. As a result, the wiring insulation may wear and …
Honda Shadow 2007–2009
In the anti-lock braking system (ABS), the rear wheel rotational speed sensor wiring connected to the control module (modulator) may be connected in reverse (left and right reversed). As a result, ABS …
日通 ― 2006
In the anti-lock brake system (ABS), the rear wheel rotational speed sensor wiring connected to the control module (modulator) may be connected with left and right reversed. As a result, ABS control …
トレクス ― 2005–2007
The boss welding at the disk plate attachment section of the jackknife prevention device is inadequate, resulting in insufficient strength in some units. Continued use may cause the boss to detach, allowing …
日通 - 2008–2009
The boss welding at the jackknife prevention device disk plate mounting location is inadequate, resulting in insufficient strength in some units. Continued use may cause the boss to detach, allowing the disk …
トレクス ― 2008–2009
The rear reflector mounting position from the vehicle's outermost edge is improper, causing non-compliance with Road Transport Vehicle Safety Standards.
キャタピラー 914G 2007–2009