Before you buy, check it isn't under a dangerous recall.

Certain rubber hoses in the hydraulic power steering system lack sufficient durability. In the worst case, these rubber hoses may crack, causing oil leakage and resulting in heavy steering feel.

Speedometer gear material in manual transmission vehicles is inadequate, causing the gear to wear; in the worst case, the speedometer may cease to function.

In carbureted engines, contact wear in the fuel pump may cause the fuel pump to malfunction or cease operation, risking engine stall.

Improper installation of the air conditioner high-pressure hose causes interference between the rear harness and the hose crimped section. Vehicle vibration may damage the harness insulation, potentially resulting in wire short circuit …

In engines equipped with electronic fuel injection, ignition system noise may cause engine malfunction, and in the worst case, engine stoppage may occur.

In electronically controlled fuel injection engines, improper routing of ground wires may cause the ground wire to be severed due to engine vibration and other factors, potentially resulting in engine shutdown.

In diesel vehicle turbochargers, the seal packing structure at the rotating shaft seal is inadequate. Continued operation in this condition may cause turbocharger lubricating oil to accumulate in the intake manifold during …

The gear (lower) in the front seat backrest adjustment mechanism lacks sufficient strength, causing gear damage. In worst cases, the backrest may collapse.

If the fuel tank's fuel piping system becomes clogged, internal pressure may rise under certain operating conditions, causing the fuel tank to deform. In the worst case, contact with the propeller shaft …

In vehicles equipped with power windows, certain driver-side switches for raising and lowering door glass have manufacturing defects. Continued use in this condition may cause internal short-circuiting of the switch, rendering the …

The check valve in the vacuum hose of the brake booster is defective due to manufacturing error. If the vehicle continues to be used in this condition, the internal components of the …

The clip attached to the fixing pin of the front brake disc is improperly assembled. Continued use in this condition may cause the clip to detach and the pin to shift, potentially …

Due to improper programming in the brake system computer, the ABS (anti-lock braking system) activates unnecessarily during normal braking operations. In worst-case scenarios, this may result in extended braking distance.

If the power door mirror switch mounted on the driver's door is operated while rainwater or similar moisture has infiltrated it, internal short-circuiting may occur, which could potentially result in fire in …

In two-wheel drive diesel vehicles, the front pipe mounting bracket of the exhaust pipe has insufficient strength, and in vehicles equipped with automatic transmissions, the main muffler mounting bracket has defective machining. …

Some airbag deployment sensors are susceptible to impacts from below the vehicle body. If the underside of the vehicle receives a severe impact, the airbag may deploy.

Certain idle pulleys (slack belt pulleys) and tension pulleys (tension-adjusting belt pulleys) on the engine timing belt (camshaft drive belt) have insufficient strength. Continued use in this condition may result in abnormal …

The frame shape of the right-side second-row seat is improper. Upon impact from collision or similar events, the seat frame and seat belt may interfere with each other, potentially resulting in seat …

The piston surface treatment within the rear brake system is inadequate. Continued use in this condition causes the cup attached to the piston to wear, resulting in brake fluid leakage. In the …

Manufacturing defects exist in the alternator diodes (semiconductors) and IC regulator (voltage regulator). Continued use in this condition may cause contact failure in these components, preventing battery charging and resulting in engine …

Manufacturing defects exist in the cam angle sensor and crank angle sensor mounted on the engine. If use continues in this condition, internal contact failure in the sensor may occur, preventing normal …

Due to manufacturing defects, cracks may be present in the upper universal joint of the steering shaft in the steering system. Continued use in this condition may result in loss of steering …

The mounting bolt of the voltage regulator attached to the engine alternator is incorrect; if use continues in this state, the bolt may loosen, and in the worst case, the battery may …

The seals in the bearing sections of the tension roller and idle roller (slack belt vehicles) that adjust the tension of the auxiliary drive belt for the engine are inadequate. Continued use …

Certain cooling fan motor bearing mounting dimensions are improper. Continued use in this condition may cause bearing seizure, motor failure, and engine overheating.

Poor electrical connections exist in the wiring inside the motor that generates hydraulic pressure in the bronze device. If use continues in this condition, in the worst case the motor may cease …

The hinge structure of the front seat backrest is inadequately designed. When lowering the backrest by hand or finger insertion into the hinge area, hands or fingers may be pinched in the …

Certain front suspension coil springs have inadequate anti-corrosion coating. Continued use in this condition may result in rust formation, and in worst case, coil spring fracture, potentially compromising driving stability.

The weld of the reinforcement plate at the vehicle body mounting point of the steering gearbox is inadequate. Repeated driving that applies excessive force to the steering shaft, such as curb strikes …

The shaft within the gearbox of the steering apparatus has been improperly machined. Continued use in this condition may cause the adjustment nut to loosen, resulting in power steering fluid leakage. In …