Before you buy, check it isn't under a dangerous recall.

In the hybrid system, due to an inappropriate control program, if a shift operation is performed during shift range calculation, an abnormality may be incorrectly detected. As a result, a warning light …

(1) In the emergency call device, the control program of the in-vehicle communication module is inappropriate, which may prevent proper conversion between voice data and communication data. Consequently, voice calls may not …

The connection nut between the gear unit on the front wheel and the speedometer cable may be improperly tightened. If use continues in this condition, the connection nut may loosen and the …

The brake servo connecting rod may have insufficient fastening torque at the connection due to improper assembly instructions during manufacturing. As a result, the bolt may become completely loose, and in the …

On large trucks, improper sub-harness routing of the LED front fog lamp may cause the connection connector to interfere with or be pinched by the front underrun protection device (FUPD) in vehicle …

In light-duty trucks, due to improper engine production processes, the fuel return hose may become crushed between the oil filter and oil level gauge guide. This can cause the fuel return hose …

On large and medium-duty trucks, improper tools were used to tighten the rear bumper mounting bolts, resulting in some bolts not being tightened to the specified torque. During use, these bolts may …

In the engine: 1. Due to inappropriate engine control programming, abnormal combustion may occur under conditions where the speed limiting device activates during continuous high-load operation. 2. Due to insufficient oil drainage …

In forklifts and similar vehicles, inadequate regulatory compliance verification may result in non-conformance with safety standards in three device categories (11 items total): small special vehicle dimensions (height, width), windshield wipers, and …

Forklifts and similar vehicles may fail to comply with safety standards in three device categories (11 items total) due to inadequate regulatory verification: dimensions (height, width) of small special-purpose vehicles, windshield wipers, …

Forklifts and similar vehicles have inadequate regulatory compliance verification, resulting in non-conformity with safety standards in three device categories (11 items total): dimensions (height, width) of compact special-purpose vehicles, windshield wipers, and …

The metal water supply tank for the toilet in large buses has insufficient strength in the tank mounting section, which can cause the mounting section to be damaged and the tank to …

The large bus toilet water supply tank has insufficient strength in the tank mounting bracket, which may cause the bracket to deteriorate and the tank to detach. This may damage the toilet …

Maximum speed limit setting is inappropriate, allowing operation beyond the maximum speed specification. When operating above 50 km/h, the first axle load of the crane vehicle exceeds tire load capacity, resulting in …

The speed unit display (km/h) on the speedometer in the instrument cluster of certain crane trucks and crane carrier vehicles does not illuminate properly, making it impossible to recognize the speed unit …

The wire harness terminal supplying power to the air conditioning blower fan regulator has improper plating material. Vehicle vibration can damage the plating, causing fretting corrosion. This increases electrical resistance, causing the …

During vehicle manufacturing, roof rail airbags may be installed with incorrect twisting. As a result, the airbag may not deploy properly upon deployment, and in the worst case, occupants may suffer excessive …

The oil seal lip on the manual shift lever shaft of the automatic transmission may be rolled over due to improper shaft assembly fixtures. This can result in oil leakage from the …

Due to communication failure in the optical axis inspection equipment at the vehicle manufacturing plant, inspection and adjustment were performed with improper optical axis settings. Consequently, the optical axis may not meet …

Improper valve guides in the engine head cause excessive wear in some units. This generates abnormal noise, and continued operation in this condition risks valve head fracture, resulting in reduced engine performance …

In large and medium-duty trucks, some units were produced with improperly manufactured lock nuts for front axle hub bearings, resulting in lock nuts with excessively large thread effective diameters being installed. Consequently, …

Due to improper circuit design in the agricultural chemical sprayer vehicle, excessive current may flow through the starter switch. This can cause the internal resin of the starter switch to melt, resulting …

In the damping device of wheel cranes, improper design of the hydraulic suspension circuit can cause abnormally high pressure to develop in the front axle suspension cylinder when traversing step obstacles while …

In the front suspension, improper control during the lower arm ball joint assembly process has resulted in some vehicles where the lower arm ball joint bolt is not properly tightened. As a …

In the ABS (anti-lock brake system) modulator, improper management of the grease application equipment has resulted in excessive grease being applied to the O-ring of the reservoir piston. As a result, repeated …

In hydrogen piping, insufficient backup ring rigidity at the pipe connection socket and molding defects in the O-ring inside the vehicle-side fill socket may cause temporary hydrogen fuel leakage under high pressure …

Tank lorry undercarriage piping: insufficient rigidity of the discharge pump bracket causes excessive loading at the piping cross-section near the pump when driving loads act on the pump, resulting in cracks in …

Due to inadequate manufacturing process control of banjo bolts that allow brake oil passage in brake calipers, bolts without the oil passage hole may be installed. This prevents brake oil supply to …

In air-suspension-equipped large trucks (4-axle vehicles), the tandem propeller shaft (propeller shaft between the rear-front and rear-rear axles) has improper length settings. When the tandem propeller is fully compressed, the spline shaft …

In road sweeper vehicles (road work vehicles), improper routing of the starter motor wiring for the work engine in the electrical harness allows the wiring insulation to melt due to heat from …