Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10558 recalls on record · page 79 of 352
The fuel hose connector in the engine compartment has insufficient heat resistance due to inadequate thermal evaluation. High temperatures in the engine compartment cause degradation and cracking, potentially resulting in fuel leakage.
The harness connected to the auxiliary power module may not have the protective cover installed under the vehicle floor due to improper work instructions. Flying debris during driving could damage the harness, …
In concrete mixer vehicles equipped with an external switch for the electric water pump, improper installation instructions have resulted in some vehicles with electrical circuits that bypass the fuse. Consequently, overcurrent during …
Improper routing of the transmission harness results in insufficient clearance between the harness and catalytic converter in some vehicles. The harness may melt due to catalytic converter heat, potentially causing engine stall …
In the power transfer unit, due to inadequate control programming, when the unit fails due to overload operation on rough terrain or similar conditions, the safe mode does not function. This results …
In the steering system of four-wheel-steer agricultural chemical spray vehicles, the attachment bolts of the steering system are tightened with improper torque. Repeated steering operations that strike the stopper can cause loosening …
③In the steering shaft, improper assembly instructions for the steering shaft have resulted in interference between the steering gear coupling bolt, causing insufficient fastening in some units. Continued use in this condition …
In the engine breather tube catch tank, improper maintenance of the catch tank can allow moisture to accumulate inside during use in cold climates. This accumulated moisture may freeze. When frozen, the …
The exhaust pipe (exhaust manifold) cover has an improper shape, which may allow vegetation and other debris to accumulate around the exhaust pipe during operation. Continued use in this condition can cause …
In the hydrostatic transmission pump of excavators and loaders, the rod and cover components of the directional control piston that switches between forward and reverse have inadequate dimensional tolerances. Frequent forward-reverse switching …
In large tour buses, heater hoses have insufficient durability and may fail prematurely. This can result in coolant leakage, and continued operation may lead to engine overheating.
Large tractors equipped with a 400-liter aluminum fuel tank may develop cracks at tank weld joints due to insufficient tank strength, which can occur from vibration during operation. Continued use in this …
The safety device switch of a vertical gate (lifting device) for loading/unloading cargo mounted on the rear of van-type trucks has improper cable routing. This may result in the safety device failing …
The transmission ground cable may have improper length, which can cause tension due to vehicle vibration and other factors. This may result in cable breakage during use, preventing engine starter operation and …
In the cooling system reservoir tank, inadequate maintenance of manufacturing equipment has resulted in insufficient welding at joint areas. This can cause coolant leakage from the joints, and in worst cases, the …
In the cooling system reservoir tank, insufficient mold verification has resulted in some units where the breather hose connection port inner diameter exceeds the standard specification. This can cause coolant leakage at …
In van-type refrigerated semi-trailers, inadequate construction management at the joints between body rails and side panels results in insufficient joint strength in some units. Due to loads during operation, cracks develop at …
Van-type refrigerated trucks have inadequate construction control at the joint between the body rail and side panel, resulting in insufficient joint strength in some units. Running loads can cause cracks at the …
The rear combination lamp on the semi-trailer does not comply with Safety Standard Article 37 (Rear Light Standard) and/or Safety Standard Article 39 (Brake Light Standard) due to improper installation instructions.
In van-type trucks with a gross vehicle weight rating of 3.5 tons or less, the mounting position of the auxiliary brake light is inappropriate and does not comply with Safety Standard Article …
In the electric power steering system of battery-powered forklifts, the steering assist setting is inappropriate, causing inertial impact forces at steering end to exceed the material strength of the rear axle and …
Fuel lines have insufficient heat resistance due to inadequate thermal evaluation. When exposed to high temperatures in the engine compartment, cracks may develop in the affected lines, potentially resulting in fuel leakage.
Certain automatic transmission oil lines have improper material composition during manufacturing, resulting in inadequate friction welding at connection points. This can cause the line connections to separate, leading to transmission oil leakage. …
On the fuel tank, the clearance between the bolt that secures the seat slide rail to the floor is small, and the bolt may contact the upper part of the fuel tank. …
In large bus clutch boosters, improper manufacturing process control has resulted in some units being fitted with oversized fixing bolts. This causes inadequate booster fastening, which can lead to fracture of the …
In the electrical wiring of snow vehicles, the panel-mount terminal block installed between the battery and fuse box was selected inappropriately, causing contact failure due to running vibration and similar factors. As …
The sliding roof glass panels may have insufficient adhesive strength due to inadequate surface treatment during manufacturing. This can cause the glass panel to lift and, in the worst case, detach due …
The occupant weight classification system in the front passenger seat cushion has improper weight calibration at manufacture, potentially causing incorrect weight detection—either lighter or heavier than actual. This may result in the …
The engine control unit's control program contains improper specification instructions for vehicle implementation, resulting in incorrect control software being installed. Consequently, noise levels may fail to meet regulatory standards.
Engine closure plugs lack sufficient durability and may fracture under engine oil pressure, resulting in engine oil leakage. In severe cases, this may cause engine damage or allow engine oil to spill …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.