Before you buy, check it isn't under a dangerous recall.

Engine closure plugs lack sufficient durability and may fracture under engine oil pressure, resulting in engine oil leakage. In severe cases, this may cause engine damage or allow engine oil to spill …

In agricultural tractors, power steering hose assembly instructions are inadequate, causing some power steering hoses to interfere with the front axle frame. Continued use in this condition may result in the power …

On small-sized frost-prevention chemical spreader vehicles, the clearance between the rear wheel fender and opposing bracket, and the tire is improper. During cornering and when crossing steps or bumps, the fender and …

The chassis frame attachment section of the rear number plate bracket stay has insufficient strength. Running vibration and similar conditions can cause cracks to develop at the attachment point. Continued use in …

On the front side member, due to improper welding equipment settings, the welding gun does not contact the vehicle body panel correctly, and there is a possibility that some weld spots are …

Electrical wiring behind the headlamp may contact the air conditioning hose fitting due to improper wiring routing. Vibrations during driving can damage the wiring insulation, potentially causing short circuits and engine stall …

In the automatic transmission, due to inadequate shift control programming, when idle-up control operates while stopped in D range, the forward clutch may enter a half-engaged state. This causes abnormal clutch wear, …

In small buses, improper confirmation during DPF muffler installation has resulted in incorrect DPF muffler specifications being installed. As a result, these vehicles may not comply with Safety Standard Article 31 (Exhaust …

Certain steel disk wheels on large trucks have inadequate rim-forming dies, resulting in uneven weld interfaces between the rim and disk. This causes insufficient fatigue strength in the welded sections. Prolonged use …

Rear spoiler adhesion is insufficient on some vehicles due to improper bonding work instructions. Vehicle vibration may cause the adhesive bond to separate, potentially resulting in rear spoiler detachment that could obstruct …

Certain fuel hoses have insufficient durability due to improper material composition. This can cause premature deterioration and cracking of the fuel hose, potentially resulting in fuel leakage.

In the continuously variable transmission (CVT), due to an inappropriate control program, the steel belt, which is the transmission mechanism, may become damaged. If the vehicle continues to be used in this …

Tie rods lack sufficient durability due to inadequate strength analysis. Under high ambient temperatures or vibration from road surfaces, they may fracture, potentially resulting in loss of steering control in worst cases.

Due to improper manufacturing tolerance settings in the starter-alternator, gaps may form in the housing. This allows moisture to enter, and if an internal circuit short occurs within the starter-alternator, it can …

Due to improper manufacturing tolerance settings on the fuel tank, some vehicles have insufficient clearance between the fuel tank and the bracket attached to the vehicle body. In a frontal collision, the …

Certain steel disk wheels for large trucks have inadequate rim-forming dies, resulting in non-uniform weld surfaces between the rim and disk. This insufficient fatigue strength in the weld can cause cracks to …

In counterbalance-type battery forklifts, insufficient transistor capacity in the travel control controller and uneven application of thermal grease cause current concentration in the transistor under high load, resulting in elevated transistor temperature. …

In the load stabilizer differential case, improper hydraulic pressure control of the operating fluid may result in leakage due to water head pressure within the case. Continued use in this condition may …

In the wheel chock storage compartment of van-type vehicles, inadequate welding control during manufacturing results in insufficient strength at the storage bracket weld. Consequently, the storage bracket weld may fracture due to …

The ISG (Integrated Starter Generator) fault diagnostic program is inappropriate. During use, oxidation film develops on the ground terminal, increasing electrical resistance and causing the ISG electrical circuit to be incorrectly diagnosed …

In headlights, when used continuously for extended periods beyond design assumptions (such as in taxi service), the aluminum coating on the reflector may peel due to heat and ultraviolet radiation from the …

In the audio amplifier, the circuit configuration is inadequate for mitigating the effects of foreign object intrusion. If a short circuit occurs in the unprotected circuit, the existing protection circuit may fail, …

In the hybrid system, the control program for abnormality detection is inappropriate. When the step-up circuit element becomes damaged during high-load driving such as rapid acceleration from extremely low speeds, the system …

The stamped mark indicating the location of the child safety lock mechanism on the rear left and right doors is positioned inappropriately, which may cause users to misinterpret the lever position as …

Certain rear suspension bolts have insufficient strength due to improper heat treatment during manufacturing. These bolts may fracture under driving vibration and similar stresses. In the worst case, rear axle alignment cannot …

The tailgate rubber stop has insufficient waterproof rating, which may allow water to enter the tail lamp from the mounting area. This can cause electrical short circuits, resulting in failure of the …

In ecocharge-equipped vehicles, certain crankshaft pulley bolts have inadequate thread root geometry, resulting in insufficient durability. When clamp load is low, the crankshaft pulley bolt may fracture and develop play, preventing correct …

In disk wheels for large trucks, improper mold adjustment during rim molding causes rim shape changes, resulting in stress concentration at the weld between the rim and disk. Some wheels have insufficient …

Some replacement rear bumper stays for medium-duty trucks lack identification markings. Consequently, compliance with Safety Standard Article 18-2 (bumper intrusion prevention device standards) cannot be verified.

On large truck disk wheels, improper die adjustment during rim forming causes rim shape deformation, resulting in stress concentration at the weld between the rim and disk. Some units have insufficient weld …