Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 124 of 175
Excessive lubricant applied to the telescopic mechanism of the steering column (which allows the steering wheel position to be adjusted forward and backward) can cause lubricant oil to drip onto the brake …
The brake fluid level detection switch attached to the brake fluid reservoir tank cap has improper material and machining precision. When brake fluid temperature rises, the switch may malfunction, causing the warning …
An incorrect component was installed in the steering rotation angle detection sensor, which corrects the deviation between steering wheel knob position and wheel rotation angle. This may cause frame noise to be …
In countermeasure parts from market action (improvement countermeasure notification number 333), the taper cone that secures the crankshaft pulley to the crankshaft has improper machining, resulting in some taper cones with oversized …
In vehicles equipped with brake boosters, brake hoses of incorrect length were installed, which in some cases interfere with the transmission case. Continued use may result in hose damage due to vehicle …
The link plate that retracts the brake shoe to its original position when releasing the brake in the rear-wheel drum brake of the braking system has insufficient strength. Repeated operations of stopping …
Some vehicles have insufficient strength in the heat shield mounting bracket attached to the exhaust pipe. As a result, the exhaust pipe and heat shield resonate during low-speed engine operation, causing cracks …
Improper dimensions of the fuel tank cap and filler neck cause the filler neck to swell due to fuel, making the fuel tank cap difficult to tighten and preventing proper sealing. Continued …
The fuel tank cap material is unsuitable, causing the cap to swell when exposed to fuel, creating a gap between the tank and cap with compromised sealing. Continued use may result in …
The air conditioning blower motor design is inadequate, causing the motor to rotate at speeds higher than intended. Prolonged use of the air conditioning at maximum fan speed can cause the motor …
The high-pressure hydraulic hose connecting the supply valve (controlling hydraulic pressure in the Active Body Control system) to the distribution joint that supplies oil to the front and rear wheels has an …
In the parking brake equalizer (a device that distributes parking brake operating force evenly to both wheels), some units have excessive gaps at the brake cable assembly point. The brake cable may …
During manufacturing, the clamp attachment position at the engine oil cooler hose connection may be improperly installed. Continued use in this condition risks the hose detaching from the connection, which could cause …
Improper welding between the side frame and front lower cross member results in insufficient weld strength in some units. Continued use may cause the weld to separate due to vibration during operation, …
The left-side sliding door interior handle linkage mechanism has improper press molding, preventing smooth operation. After opening the sliding door from inside the vehicle, part of the linkage mechanism may not return …
The relay emergency valve, which controls air supply and air pressure in the trailer air brake system, had no designated periodic replacement parts or repair parts specified, resulting in parts not being …
The relay emergency valve controlling air supply and air pressure in the trailer air brake system had no designated replacement intervals or service parts specification, resulting in no component replacement being performed. …
The wind-blocking insulator mounted in front of the air conditioning condenser in the engine room is made of inappropriate material. During use, this insulator may fracture at the mounting point. If the …
Some steering linkage intermediate arm brackets have insufficient strength. Continued use may cause cracks to develop in the bracket, and in worst cases, bracket failure could result in loss of steering control.
Insufficient contamination prevention measures in the brake light switch allow foreign matter ingress. When work gloves coated with insulating grease contact the switch exterior, trace grease components can gradually diffuse to the …
On vehicles equipped with auto-step, due to inappropriate programming in the auto-step controller, if the brake is depressed two or more times per second while the engine is off and the auto-step …
On shuttle buses, improper tire toe angle can cause studless tires to contact the drag link when the steering wheel is turned to maximum lock while crossing an uneven surface. Continued use …
On passenger buses, due to improper tire toe-in angle, when studless tires are installed and the steering wheel is turned to maximum lock while crossing a step or curb, the tire may …
In the Vehicle Stability Assist (VSA) system, some control units have damaged capacitors due to improper manufacturing processes. As a result, electrical noise generated by voltage fluctuations is not filtered, which can …
The brake light switch contacts lack sufficient electrical load capacity, causing contact welding during brake actuation. This results in: (1) brake lights remaining continuously illuminated, which can cause the brake light switch …
During steering cylinder assembly, improper instructions caused some hydraulic hoses to be assembled in a twisted state. As a result, when the steering is turned sharply with the tires in a tilted …
The fuel injection pipe geometry is inappropriate, causing resonance in the mid-speed range that cracks the pipe. Continued operation results in fuel leakage into engine oil; the contaminated oil mixes with blow-by …
The fuel injection pipe shape is improper, causing resonance in the mid-speed range that can crack the pipe. Continued operation risks fuel leakage into engine oil; the contaminated oil enters the crankcase …
Injuries — The product poses a serious risk of injuries because there is a possibility that the side/curtain airbag may have been wired incorrectly. In this case the side/curtain airbag may deploy …
Certain vehicles have improper attachment of the left door outer handle cable, which may cause the door to open during a side-impact collision.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.