Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 35 of 173
The low-pressure fuel pump was insufficiently validated against fuel composition. Fuel components contained in Japanese-specification fuel may adhere to and accumulate on the gerotor (metal gear pump) section of the low-pressure fuel …
The control program for the collision mitigation brake in the driving support system is inadequate, preventing correct recognition of guide posts on curved roads and the direction of travel of oncoming vehicles. …
The engine controller's idle intake air volume control program is improper, which may result in insufficient intake air volume while the vehicle is stopped in Drive range. This can cause a decrease …
The rear-end lower panel has an improper shape. Running vibration may cause the main wire harness to contact this panel. This can damage the harness insulation, causing internal wiring short circuits, which …
In the front hub bearing of large truck low-floor 4-axle vehicles, excessive interference fit with the knuckle shaft may damage the bearing during front hub assembly. Consequently, bearing damage during use may …
In the intake air preheating device that assists cold-start operation of the engine, insufficient degassing during water-resistant and rust-preventative coating of the preheater relay may allow gas bubbles to remain on the …
In the steering apparatus of low-floor dual-axle heavy-duty trucks, the clamp bolt/nut fastening torque on the left side of the front-front axle tie rod is inappropriate, resulting in reduced clamp clamping force …
On large trucks, the pre-plating acid pickling process for the fixing clamp fastening bolt on the right-side tie-rod end of the front axle is inadequate, causing some bolts to have reduced strength …
In large trucks, improper assembly of the front-wheel brake chamber in the braking system (2) results in insufficient fastening torque on the plug (closure cap), test nipple, and brake hose connection (nipple …
In large trucks equipped with air suspension and vehicle-height adjustment devices, the shock absorber piston structure is inadequate. Lateral forces cause excessive contact pressure between the piston and cylinder. Repeated cycles of …
In large trucks, the battery hold-down plate has an improper shape, causing the power cable to interfere with the plate edge when attached to the battery terminal. Continued use in this condition …
On tire rollers, if the fuel tank cap is not properly installed after refueling, water may enter the fuel tank through the filler opening. If water accumulation exceeds the water separator capacity …
In the GM (Grand Module), due to improper electrical load design, operating the brake while sounding the horn may trigger a brake light failure warning. The brake light may not illuminate until …
The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to fuel absorption caused by inadequate molding conditions that result in low resin density. This can cause …
The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to inadequate molding conditions resulting in low resin density, causing expansion when exposed to fuel. This can …
In the dashboard, due to inadequate manufacturing control, the skin is not properly welded to the carrier in some units. As a result, when the passenger-side airbag deploys during a collision or …
In the rear axle U-bolt nut tightening process for small trucks, improper fastening equipment settings result in insufficient tightening torque on some units. Continued operation may cause the nut to loosen and …
In vehicles equipped with the optional emergency brake system, certain display units have improper manufacturing specifications at the LCD panel mounting section, resulting in missing waterproof treatment. Rainwater and other moisture can …
The drawbar support (coupling device) on agricultural tractors has insufficient fastening bolt strength, which can result in fastening bolt failure. This may cause an agricultural work trailer attached to the tractor to …
Excessive grease was applied to the O-ring of the reservoir piston in some ABS (anti-lock brake system) modulators due to inadequate management of the grease application equipment. As a result, grease that …
In large-size transit buses, the engine ECU control program is inadequate, which may cause maximum combustion pressure to exceed the allowable limit of the connecting rod. Continued operation in this condition may …
In the integrated brake system hydraulic circuit control unit, improper manufacturing equipment settings result in inadequate welding between the hydraulic pump motor rotor and shaft in some units. Consequently, the rotor may …
In the electric brake booster, the mounting position of the magnet on the motor shaft of the rotational angle sensor, which is an internal component, is improper. This may cause the software …
The engine control computer has an inappropriate control program. When the throttle is opened during starting, ignition control does not function properly, and engine stall may occur during acceleration or re-acceleration after …
The engine control computer has an inappropriate control program. Carbon deposits accumulate in the combustion chamber, and portions may flake off and lodge in the seat surface of the exhaust or intake …
Due to inadequate work management, the retainer securing the brand emblem on the driver-side airbag cover may not be properly installed. Upon airbag deployment, the brand emblem or retainer may scatter, potentially …
Dashboard harness routing is improperly designed, allowing contact with the steering column. Vehicle vibration may damage the harness, potentially causing horn, windshield wipers, ADAS (advanced driver assistance systems), driver airbag, or turn …
In the brake booster, the fastening torque specification for the fixed nuts is inadequate, resulting in two locations not being properly torqued. Consequently, the fixed nuts may loosen during use, causing abnormal …
The cable harness for the brake fluid level sensor may contact the exhaust manifold heat shield due to inadequate assembly control during manufacturing. This can cause the insulation to be damaged by …
The driver-side airbag units shipped as replacement parts have improperly welded brackets for attachment to the steering wheel. During use, the weld points may crack and separate, potentially causing the airbag to …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.