Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 40 of 173
Certain rear suspension bolts have insufficient strength due to improper heat treatment during manufacturing. These bolts may fracture under driving vibration and similar stresses. In the worst case, rear axle alignment cannot …
In ecocharge-equipped vehicles, certain crankshaft pulley bolts have inadequate thread root geometry, resulting in insufficient durability. When clamp load is low, the crankshaft pulley bolt may fracture and develop play, preventing correct …
Front suspension coil springs have insufficient paint adhesion to the steel material. When sand or gravel becomes trapped, the paint coating peels easily and corrosion progresses rapidly. Continued use may result in …
Due to inadequate component management in dashboard panels, some vehicles are equipped with dashboard panels where the passenger-side airbag is not properly installed. Upon airbag deployment, this may damage the dashboard panel, …
The inflator (inflation device) of the head airbag system may have absorbed moisture due to inadequate humidity control during manufacturing. As a result, when the head airbag deploys, inflator pressure may become …
In door inner release handles, improper assembly may result in cable connection pins not being correctly installed. Consequently, operating force on the handle may not be transmitted to the door latch, potentially …
In passenger-side airbag modules, improper stitching of the airbag results in insufficient strength at the stitched seams. Upon airbag deployment during a collision, the stitched seams may tear, preventing normal expansion and …
The ABS control module has improper circuit design, causing continuous power supply even when the engine is off. This can cause the connector to overheat and melt, burning the harness, and in …
In some steering hose ferrule portions of the steering apparatus, the pressure rating evaluation of the operating hydraulic fluid is inadequate. When excessive operations such as repeated full lock-to-lock steering maneuvers are …
The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to fuel absorption caused by inadequate molding conditions, resulting in lowered resin density. This can cause the …
The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to fuel absorption caused by inadequate molding conditions that result in low resin density. This can cause …
The impeller (resin rotor) in the low-pressure fuel pump may swell and deform due to fuel absorption caused by improper molding conditions that result in low resin density. This can cause the …
The side stand spring has an improper shape, resulting in insufficient durability. Consequently, the spring may fracture due to vibrations during operation, causing the side stand to drop. In the worst case, …
The Electronic Control Unit (ECU) has an improper fuel injection control program. When upshifting with the quickshifter in high engine load conditions, excessive combustion may occur in the exhaust passage. This creates …
Front brake pad bonding to the plate may be insufficient due to inadequate manufacturing process control. This can lead to corrosion from moisture and other factors, causing the brake pad to separate …
In the Vehicle Stability Control (VSC) system, due to an inappropriate control program, vibrations during idling while the vehicle is stationary may be incorrectly detected as vehicle speed by the two-wheel-drive speed …
In some front and inter-axle propeller shafts, thrust washers are not installed inside bearing cups due to inadequate manufacturing control of universal joints. This causes bearing cup play to damage seals, resulting …
In the intake air preheating device that assists cold-start operation of the engine, insufficient degassing during waterproofing and corrosion prevention treatment of the preheater relay may rarely allow air bubbles to remain …
In large-size transit buses, the engine ECU control program is inadequate, which may cause maximum combustion pressure to exceed the connecting rod tolerance limit. Continued operation in this state may result in …
In the right lower arm of the front suspension system, insufficient component fixation during the welding process causes misalignment of the weld position, resulting in insufficient weld strength in some units. Braking …
The rear spoiler attached to the tailgate has inadequate work instructions in the adhesive application process, resulting in reduced bonding between the upper and lower portions of the rear spoiler in some …
In the engine, the nuts fastening the cylinder head have been improperly machined, resulting in stripped threads in some units. This causes insufficient clamping force on the cylinder head, which compromises the …
On the front axle of shovel loaders, hydrogen content management is insufficient during the steel manufacturing process of the axle shaft, resulting in internal cracking of the axle shaft. In the worst …
On the front axle, improper manufacturing equipment settings have resulted in insufficient welding of the left front lower control arm bracket. Consequently, the bracket may fracture due to driving vibration and other …
In the front axle of the shovel loaders, the oil seal assembly instruction was inappropriate, causing deformation of the oil seal in some units. Continued use in this condition may result in …
On medium-duty trucks, the insulation bushing shape of the 60A-specification alternator positive terminal is inadequate. When moisture containing snow-melt compounds accumulates between the terminal and alternator body, leakage current may occur. This …
In detachable container vehicles, some units lack fuses in the power circuit for the electric retractable rear bumper due to improper wiring diagram specifications. When wiring shorts, excessive current flows, potentially causing …
In the braking system of wheel cranes, due to inappropriate selection of the primary brake power cluster, residual pressure may remain in the brake fluid pressure circuit even after the brake pedal …
The rear brake pipe assembly method is improper, resulting in some brake pipes not being correctly attached to their supports. This causes excessive loads on the brake pipes during vehicle operation due …
The engine control unit (ECU) has inappropriate alternator control logic. When battery charge is low, engine vacuum may decrease during cold starts or when driving on long downhill slopes. This can result …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.