Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 93 of 175
The engine air intake duct retaining clip may crack when excessive force is applied during clip removal. Reusing a cracked clip allows the crack to propagate, potentially causing clip failure during operation. …
Priming pumps in diesel engine vehicles may have elevated residual stress from molding. Ozone degradation during use can cause cracking. If use continues, cracks may propagate through the wall, leading to fuel …
Due to improper software in the body electrical control unit, when attempting to start the engine, the unit may fail to transmit the signal necessary for engine starting even upon receiving the …
In large truck air brake systems, the air tube above the DPF device lacks sufficient heat resistance. Exposure to DPF device heat can cause partial melting of the air tube, resulting in …
In air brake systems of large trucks, the reducing valve (a pressure-reducing valve that switches pressure between the air tank for 4-axle rear air suspension and the brake air tank) within the …
In air brake systems of large trucks and buses, the safety valve (which opens to reduce pressure when air lines become over-pressurized for protection) has insufficient air discharge capacity. When air lines …
The brake system vacuum hose may interfere with a plastic engine cover due to improper assembly direction guidance. Continued long-term use in this condition may cause the hose to perforate, resulting in …
In three-axle semi-trailers for transporting bulk cargo with relaxed divisible load standard specifications, the structural evaluation of the vehicle body (subframe) is inadequate. Consequently, stress generated during operation may concentrate on the …
Due to improper manufacturing processes, some ABS (Anti-lock Braking System) hydraulic units contain foreign matter. In the worst case, the ABS may not operate properly.
At the fuel hose attachment point of the fuel pump, the resin component material is inappropriate, causing fine cracks to develop on the fuel contact surface. As cracks propagate, fuel leakage can …
In i-Stop equipped vehicles, due to an improper program in the electric power steering control computer, the power steering function may rarely fail to operate after the engine automatically restarts from idle …
Vehicles without fuel pipe protector installed in the engine compartment may have increased risk of fuel leakage in the event of collision. Fuel pipe protector to be added to reduce this risk. …
Improper wiring length in the fuel pump circuit causes incomplete connection between the fuel pump-side connector and vehicle wiring-side connector. This results in poor electrical contact due to wear, which may melt …
In the electric power steering computer, inadequate humidity control of the terminal spacing and coil wire in the sealed motor drive relay can result in moisture absorbed by the coil wire during …
During prolonged parking in intense sunlight, when the vehicle interior reaches high temperatures, differences in thermal expansion rates among the electric column lock components that lock the steering wheel can prevent the …
The specification of the left and right main harness guide mounting bolts is inadequate, which may cause the bolts to loosen and fall out due to vibration. In the worst case, the …
The spindle that transmits engine output to the wheels via a reduction gear has a step section machined to an improper shape, resulting in insufficient durability against stresses generated during use. Continued …
The obstacle detection software for the millimeter-wave radar in the pre-collision safety system (forward collision mitigation system) is inadequate, causing the system to occasionally misidentify diffuse millimeter-wave reflections as obstacles ahead. This …
In four-wheel drive vehicles equipped with a vehicle stability control system, an incorrect two-wheel drive control program was written to the stability control unit. When braking slowly on icy roads and similar …
Some front brake hose joints have incorrect connection positions. During hard braking, the ABS system may malfunction and lock the front brakes.
In vacuum-assisted brake boosters (master power units), improper housing crimp positioning during manufacturing can cause the seal that maintains vacuum inside the booster to shift when the brake pedal is depressed, resulting …
In medium-duty trucks and large/medium-size buses, insufficient head bolt torque on the air compressor center section causes pressure oscillation from piston reciprocation to crack the seat gasket (which maintains air/coolant passage sealing …
Primary braking system brake pads exhibited insufficient adhesion between friction material and backplate. Depending on use environment, water infiltration at the adhesion interface can cause corrosion, potentially resulting in friction material separation …
The air conditioning evaporator may develop internal corrosion and perforation due to improper manufacturing methods when combined with certain compressors, causing refrigerant and lubricating oil leakage. This results in reduced air conditioning …
Due to improper programming in the airbag control unit, side airbags may deploy with delay or fail to deploy upon lateral impact.
In the electronically controlled brake system, the accumulator (pressure reservoir) had insufficient strength analysis. During vehicle operation, vertical vibrations can impose significant stress on portions of the pressure vessel. Consequently, fatigue cracks …
Cracks develop in the tabs of the high-mounted stop lamp due to the effect of lubricant applied to the high-mounted stop lamp fixed to the tailgate. Continued use in this condition may …
On vehicles equipped with ACC (Adaptive Cruise Control system that automatically maintains following distance behind preceding vehicles) and FCM (Forward Collision Mitigation system that automatically applies brakes to reduce collision damage), improper …
①Due to improper manufacturing process of circuit elements monitoring microcontroller power supply voltage within the Electric Power Steering Control Unit (EPS ECU), some elements exhibit characteristic defects. Consequently, the power supply voltage …
The coil mold and wiring fixing method of solenoid valve components mounted on road rollers are improper, causing the coil mold to wear due to mechanical vibration during operation. Continued use allows …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.