Before you buy, check it isn't under a dangerous recall.

In the passenger seat airbag inflator, improper handling during equipment shutdown in the igniter charge filling process may result in insufficient charge quantity. This could prevent proper airbag deployment during activation.

The inflator (inflation device) in the passenger seat dual-stage deployment control airbag has inadequate moisture prevention for the gas generant, which may degrade due to repeated temperature and humidity fluctuations. This may …

The fuel tank vent pipe connecting to the charcoal canister has an improper shape. When the fuel tank is full and the vehicle is parked on the sidestand, fuel sloshing inside the …

The welding position of the pipe nut for trailing arm attachment on the right rear floor side member is improper, resulting in insufficient weld strength in some vehicles. Continued use may cause …

The fuel level sender unit in the fuel tank has improper fastening torque on the attachment screws, causing deformation of the rubber gasket at the mounting point. This compromises the seal integrity. …

In rotary snow removal equipment mounted on excavator-loaders, improper battery cable installation instructions can cause the cable to interfere with hydraulic hoses due to vibration during operation, potentially damaging the hose covering. …

In front seat belts, improper manufacturing of the seat belt pretensioner has resulted in some units with improperly assembled gas generators. Consequently, when the pretensioner activates during a collision, the gas generator …

In wheel crane braking systems, improper manufacturing of brake calipers results in low cap fastening torque. During brake actuation, hydraulic pressure may cause the cap to loosen. Continued operation in this condition …

In articulated buses, the mounting method of the engine inspection access panel installed on the rear of the vehicle body is inappropriate, resulting in insufficient adhesive strength in some units. Continued operation …

In articulated buses, improper edge finishing of the wiring securing bracket in the power distribution box behind the driver's seat may cause wiring to interfere with the bracket's edge. If use continues …

In articulated buses, inadequate modifications to comply with one-man-operation bus structural requirements may allow the middle and rear doors to open by driver operation even when passengers are present near these doors. …

During transmission maintenance operations, improper instructions in the work procedure may result in the transmission control module's control program not being set correctly. Consequently, when driving in automatic shift mode, the half-clutch …

In semi-automatic hydraulic clutches, insufficient evaluation of vibration resistance at the clutch hydraulic pipe connection has resulted in engine vibration causing the connection retention pin to detach. This can damage the pipe, …

In the electrical system, the routing of the regulator wiring is improper in some vehicles, causing the wiring to contact the regulator bracket. As a result, the insulation may be damaged by …

In large trucks, improper assembly procedures for the heat shield of the emission control evaporative system resulted in some vehicles being equipped with incorrect heat shield specifications. This causes the distance between …

Bolts and nuts for fixing opposing brackets that secure the chassis frame and sub-frame on medium-duty dump trucks were manufactured improperly, resulting in incorrect parts being installed.

On medium-duty dump trucks, the winch carrier mounting bolts are improperly installed with insufficient tightening torque, resulting in reduced axial preload. Continued operation in this condition may cause the bolts to loosen …

The ESP (Electronic Stability Program) control unit has an inadequate control program, which fails to manage tire slip during rapid acceleration on wet road surfaces, causing severe vibration in the drivetrain and …

In the front air suspension, improper manufacturing of the air bellows can cause the support ring (retaining bracket) to detach due to vibration during driving, resulting in air bellows damage. This may …

The power distribution module's circuit board was coated with moisture-resistant material while retaining unnecessary solder residue from manufacturing. During use, cracks can develop in this coating. In high-humidity environments, this allows fine …

In refuse collection containers for detachable container-equipped vehicles, welding between the rear member and rear cover is inadequate. Vibration during operation may cause cracks to develop at the welded joint. Continued use …

On vehicles equipped with 24V tailgate lifters, improper selection of rear reflectors and backup lights results in reflective characteristics of the rear reflector and light distribution characteristics of the backup light failing …

① On vehicles equipped with a 12V power tailgate lifter, the rear reflector has improper selection, resulting in reflective characteristics that do not meet the standard values and do not comply with …

In large trucks, the clamping section assembly of the front axle tie rod end on the front two-axle vehicle is improper, resulting in insufficient fastening torque on the mounting bolt. If the …

In large trucks, improper assembly of the Power Take-Off (PTO) device has resulted in adhesive residue from corrosion-prevention tape remaining on the shaft surface during pulley installation. This causes insufficient bolt clamping …

In large trucks, the vehicle master control unit program that controls wiper operation has improper logic. If certain operations are performed while the wipers are operating, the wiper control may enter a …

In large trucks, the battery fixed plate has an improper shape, causing the power cable to interfere with the edge of the fixed plate when attached to the battery terminal. Continued use …

Driver-side airbag inflators may have inadequate moisture protection of the gas generant. Under high-humidity environments with repeated large temperature fluctuations, the gas generant can degrade. This may cause inflator container rupture during …

In the Electronic Stability Program (ESP), due to an inadequate control program in the ESP control unit, if communication between the unit and the driver assistance system is lost while cruise control …

The control program that monitors the driver's seat belt buckle status in the seat belt non-fastening warning system is inappropriate. When the engine is started under specific conditions, the warning lamp does …