Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 124 of 355
In the air cleaner box, due to improper molding equipment for the blow-by gas passage, a resin membrane remains in the blow-by gas passage and is not fully penetrated in some units. …
In rear reflectors, improper manufacturing may result in the reflector surface (lens portion) not being correctly formed. This may cause insufficient reflected luminous intensity, failing to comply with Safety Standard Article 38.
In the power transmission system, the fastening structure of the belt-drive pulley is inadequate, which may cause the pulley fastening nut to loosen during operation. This can result in the pulley contacting …
The potentiometer sensor that detects lever position in the main transmission lever of the harvester-thresher has insufficient grease in its rotating component due to improper manufacturing. Consequently, the seal material in the …
The potentiometer sensor that detects lever position in the main transmission lever of the combine harvester has inadequate design. Extended use causes wear of the internal contact sliding surface, and wear debris …
In the hydrostatic transmission of a combine harvester, the structure of the emergency operation levers for turning and straight travel is inadequate, allowing rainwater and other moisture to seep into the base …
In the two-stage airbag device on the driver's side, improper manufacturing of the inflator has resulted in some units where the second-stage gas generator is not filled to design specifications. Consequently, the …
In the driver and front passenger seat heaters, improper routing of electrical wiring in the heater switch may cause the seat heater to continue operating even after the engine is stopped while …
In the electronic stability program (ESP), improper manufacturing of the hydraulic pressure regulator (ESP block) that controls brake fluid pressure may prevent electronic control of brake fluid pressure adjustment. Consequently, the anti-lock …
In medium-duty trucks, the attachment bracket for the underrun protection device has insufficient strength. When the underrun protection device contacts pavement irregularities or similar obstacles, cracks may develop in the attachment bracket. …
For large truck and bus engines, fuel injection system periodic cleaning information was not provided to users and automotive service providers. Without cleaning, fuel temperature variations can generate compounds in the fuel, …
The fuel tank cap seal evaluation and the dimensions of the packing holder assembled to the cap are inadequate. When the packing deforms due to fuel, the packing may shift when the …
Door mirror switches have inadequate surface treatment on the movable contacts inside the mirror switch. During switch operation, the movable contacts wear, generating wear particles. If use continues in this condition, wear …
During final inspection at the vehicle manufacturing plant, some vehicles were inspected and approved/rejected by non-designated inspectors, resulting in improper inspection compliance with safety and environmental performance standards (safety regulations).
Driver-side or passenger-side airbag inflators may experience degradation of the gas generant due to inadequate moisture protection. When exposed to high-humidity environments with repeated large temperature fluctuations, the gas generant can deteriorate. …
Driver or front passenger airbag inflators may have inadequate moisture-prevention treatment of the gas generant. Under high humidity conditions with repeated large temperature fluctuations, the gas generant may degrade, potentially causing the …
On large truck low-floor four-axle vehicles, the preload setting value for the front hub bearing specified in the maintenance manual is inappropriate, potentially resulting in excessive bearing preload. Additionally, when inserting the …
On refrigerated vehicles, the U-bolts securing the longitudinal floor beams to the chassis frame (referred to as "longitudinal beam U-bolts") are positioned improperly. During off-road driving, these may interfere with the U-bolts …
Due to improper programming in the airbag control module, signals to deploy the front airbags and pretensioners during a frontal collision are not transmitted. As a result, the front airbags and pretensioners …
The meter panel control unit program that controls seatbelt non-wearing alerts is inappropriate. Therefore, while driving with the seatbelt unfastened, the alert specified in the technical requirements of Regulation No. 16 of …
In the occupant protection system, the wiring routing of the front impact sensor is improper, which may cause the wiring to break before collision detection occurs during a collision. As a result, …
In the electrical system, improper steering column design allows sand and dust to enter the steering column. During steering operations, wiring inside the steering column may contact sand and dust, causing disconnection. …
In the engine cooling system, improper routing of the turbocharger coolant return hose causes high-temperature coolant to return directly to the reservoir tank, leading to premature degradation and cracking due to heat …
In the front windshield wiper system, the linkage rod that transmits driving force from the wiper motor to both wiper arms has inadequate design, resulting in insufficient strength. As a result, the …
The bracket securing the air spoiler surface to the base on the rear of the vehicle has insufficient strength. Vibration during driving may cause cracks to develop in the bracket. Continued use …
The engine control unit's misfire detection program is inappropriate, which may cause the system to detect a misfire even when none is occurring. This triggers failsafe mode control, illuminating the MIL (engine …
In the brake system, improper routing of the brake air tube may cause contact with the propeller shaft when driving on rough roads with significant elevation changes. Continued operation in this condition …
Due to improper programming of the all-wheel-drive control unit, driving on slippery road surfaces may result in inappropriate distribution of driving force to the rear axle. This can cause excessive distribution of …
In vehicles equipped with LED-type front lighting, the onboard supply control unit program that controls parking lights is inadequate, causing parking lights to flash when the turn signal or emergency flasher is …
The gateway control unit program that controls brake light illumination is inappropriate. When emergency braking is activated, the brake signal is not transmitted to the body control module, causing the brake lights …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.